Use the risk matrix in Table 1-14 to determine the risk level for the Bhopal incident. Estimate
Question:
Use the risk matrix in Table 1-14 to determine the risk level for the Bhopal incident. Estimate the severity category, the safety severity level, the likelihood, and the risk level.
Transcribed Image Text:
Table 1-14 Risk Matrix for Semi-Quantitative Classification of Incidents Risk Matrix 1. Select the severity from the highest box in either of columns 1, 2, or 3. Read the Category and Safety Severity Level from the same row. S e V e 11 t 2. Select the likelihood from columns 4 through 7. TMEF: Target mitigated event frequency (yr-1). 3. Read the Risk Level from the intersection of the severity row and the likelihood column. TQ: Threshold quantity-see Table 1-15. 1 Human health impact 3 Se Safe ve ty Fire, Chrit seve explosi emi yrity level 2 Recordable injury on cal direct imp c cost ($) act a e Public fatality possible, x tro TM employee $10 TQ|ph|EF = 10 fatalities million likely Greater 2 Ca 4 than 20 tas Employee $19 Ve 3 fatality million to ry possible, to 100 years Risk level B Risk level C Negligible risk 7 IMPROBABLE, BUT NOT IMPOSSIBLE Not expected to happen anywhere in the division over the life of the plant > 1000 years Risk level C Risk level D Negligible risk Risk level A: Unacceptable risk; additional safeguards must be implemented immediately. Risk level B: Undesirable risk; additional safeguards must be implemented within 3 months. Risk level C: Acceptable risk, but only if existing safeguards reduces the risk to as low as reasonably practicable (ALARP) levels. Risk level D: Acceptable risk, no additional safeguards required.
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 100% (2 reviews)
We must estimate the severity category safety severity level likelihood and risk level for the Bhopa...View the full answer
Answered By
Benard Ndini Mwendwa
I am a graduate from Kenya. I managed to score one of the highest levels in my BS. I have experience in academic writing since I have been working as a freelancer in most of my time. I am willing to help other students attain better grades in their academic portfolio. Thank you.
4.90+
107+ Reviews
240+ Question Solved
Related Book For
Chemical Process Safety Fundamentals With Applications
ISBN: 9780134857770
4th Edition
Authors: Daniel A. Crowl, Joseph F. Louvar
Question Posted:
Students also viewed these Engineering questions
-
Risk Assessment Homework In this assignment, you will perform a qualitative risk assessment, using a template that has been provided below. A listing of threats has been prepopulated for you. These...
-
In October 1995, the United Kingdom Committee on Safety of Medicines (CSM) issued a warning to 190,000 general practitioners, pharmacists, and directors of public health about oral contraceptive...
-
Construction projects encounter significant risks and uncertainties in term of safety, cost, time, and quality. These risks threaten the successful completion of these projects, slow down the pace of...
-
Under California Law, does a client Carmen Leake have an affirmative defense to inability to pay child support where a parent's inability to pay is due to unwillingness to work, if that parent is...
-
Control lever ABC fits loosely on an 18-mm-diameter shaft at support B. Knowing that 130 P = N for impending clockwise rotation of the lever, determine (a) The coefficient of static friction between...
-
What is an entrepreneur? Give a brief description of the entrepreneurial profile.
-
The balance sheet data for Quick Care, Inc. September 30, 2010, follow: Requirement 1. The following are three independent assumptions about the business during September. For each assumption,...
-
A telemarketing firm has studied the effects of two factors on the response to its television advertisements. The first factor is the time of day at which the ad is run, while the second is the...
-
ii. A gun of mass 0.7 tonne fires a shell of mass 8kg with a velocity of 850m/s . Determine: The initial velocity of the recoil The uniform force necessary to stop the recoil of the gun in 375 mm
-
Codes, standards, and regulations: Go to the www.osha.gov web site and look up the OSHA regulation CFR 1910.119: Process Safety Management of Highly Hazardous Chemicals. Use Appendix A to determine...
-
Accident and loss statistics: If the U.S. population in 2014 was 325 million people, calculate the deaths per 100,000 people from lightning strikes using the total fatalities from lightning in Table...
-
Determining and interpreting fixed cost variances Smitter Manufacturing Company established a predetermined fixed overhead cost rate of $200 per unit of product. The company planned to make 19,000...
-
If you were born in or after 1960, you cannot age collect "full" Social Security retirement benefits until age 67 but many begin collecting as early as age 62. If you wait to collect Social Security...
-
Check whether the sections shown in Figure 3 are underreinforced or not. If underreinforced, calculate the ultimate moment capacities. Materials are C20 and S420. Use material factors Yms, Ymc. Take...
-
In your reflection post, address the following issues: Identify a communication principle contained within this verse. Provide an example of this principle in action in your own life or in society .
-
Provide peer-reviewed references for this question, thank you: When financial managers make key operating, investing, and financing decisions, why should they worry about the time value of money?...
-
UPI Industries Ltd., a Canadian corporation with a head office in Nova Scotia, has recently been designated a public corporation. Its shares are traded on the TSX Venture Exchange. Over the past...
-
The following accounts are taken from the December 31, 2010 adjusted trial balance of the Reed Company: Cost of goods sold .........$121,120 Interest expense ........... 4,880 Depreciation expense...
-
Reread the discussion leading to the result given in (7). Does the matrix sI - A always have an inverse? Discuss.
-
Consider the least-squares problem in Figure 4-11. (a) Suppose that a single new measurement produces a y value of 2.58. Find the corresponding x value and its uncertainty. (b) Suppose you measure y...
-
Consider the linear calibration curve in Figure 4-13, which is derived from the 14 corrected absorbances in the shaded region at the right side of Table 4-7. Create a least-squares spreadsheet like...
-
Detection limit. In spectrophotometry, we measure the concentration of analyte by its absorbance of light. A low-concentration sample was prepared, and nine replicate measurements gave absorbances of...
-
Locate the centroid y and determine the moment of inertia for the shaded area about the x axis. Summarize your answer at the end of your solution. 0.4 m 0.05 ml -0.3 m 0.2 m 0.2 m '0.2 m 0.2 m
-
Baier & Smith formed a partnership under the name Brooks & Pats Plumbing. On Jan.1 2016, Baier contributed $3000 cash, plumbing supplies of $3,700, and a van with a market value of $25,000, which...
-
Ethylene glycol is heated from 25C to 40C at a rate of 2.5 kg/s in a horizontal copper tube (k = 386 W/m-K) with an inner diameter of 0.02 m and an outer diameter of 0.028 m. A saturated vapor (Tg =...
Study smarter with the SolutionInn App