Ball bearings are widely used in industrial applications. You work for an industrial food machinery manufacturer...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
Ball bearings are widely used in industrial applications. You work for an industrial food machinery manufacturer and your role is to design the driveshaft assembly on a new type of equipment that involves V-belt pulleys. Your manager asked you to select the appropriate ball bearing that satisfies the load rating of the existing application. Your co-worker, responsible of shaft design, calculated reactions on both ends of the shaft to be Ry,g = -89.2 N 0, REE = -174.4 N. Ryo = -163.4 N and R20 = 107 N. The 35-mm-diameter countershaft is to run at 1500 rev/min and the bearings are to have a life of 60 kh at a combined reliability of 0.98, assuming distribution data from manufacturer 2 in Table 11-6. Use an application factor of unity. 300 400 150 250 dia. 300 dia. 50 N 270 N Figure.2: Countershaft and pully assembly (Dimensions in mm) (a) Obtain a Basic Dynamic Load Rating for a ball bearing at both ends O and E. (b) Use an online bearing catalogue of SKF. TIMKEN and NSK to fill out the data sheet below for the indicated bearing types that satisfies the needed Basic Load Rating and the geometry requirements. Manufacturer Bearing type load Limiting speed Manufacturer designated serial number Basic static rating Deep groove ball bearing Single row angular contact ball bearings Deep groove ball bearing, thin-section 61000 series SKF SKF TIMKEN NSK Single-row groove ball bearing deep Ball bearings are widely used in industrial applications. You work for an industrial food machinery manufacturer and your role is to design the driveshaft assembly on a new type of equipment that involves V-belt pulleys. Your manager asked you to select the appropriate ball bearing that satisfies the load rating of the existing application. Your co-worker, responsible of shaft design, calculated reactions on both ends of the shaft to be Ry,g = -89.2 N 0, REE = -174.4 N. Ryo = -163.4 N and R20 = 107 N. The 35-mm-diameter countershaft is to run at 1500 rev/min and the bearings are to have a life of 60 kh at a combined reliability of 0.98, assuming distribution data from manufacturer 2 in Table 11-6. Use an application factor of unity. 300 400 150 250 dia. 300 dia. 50 N 270 N Figure.2: Countershaft and pully assembly (Dimensions in mm) (a) Obtain a Basic Dynamic Load Rating for a ball bearing at both ends O and E. (b) Use an online bearing catalogue of SKF. TIMKEN and NSK to fill out the data sheet below for the indicated bearing types that satisfies the needed Basic Load Rating and the geometry requirements. Manufacturer Bearing type load Limiting speed Manufacturer designated serial number Basic static rating Deep groove ball bearing Single row angular contact ball bearings Deep groove ball bearing, thin-section 61000 series SKF SKF TIMKEN NSK Single-row groove ball bearing deep
Expert Answer:
Related Book For
International Business and the New Realities
ISBN: 978-0136090984
2nd Edition
Authors: S. Tamer Cavusgil, Gary Knight, John R. Riesenberger
Posted Date:
Students also viewed these mechanical engineering questions
-
1. Design the state Moore machine given in Figure 6. The state machine is positive edge triggered. Include a reset to your state machine. Simulate and verify your results with a test bench file. SI...
-
Bespoke Inc. has manufactured a machine specifically to the design of its customer. The machine could not be used by any other party. Bespoke Inc. has never manufactured this type of machine before...
-
desig SIMD machine on VHDL as mesh interconnections - design node entity and arhitecture and test - design mesh entity add arhitecture adding 9 nodes as component - draw waveform to Run this...
-
A gaseous mixture consists of 80.0 mole percent N2 and 20.0 mole percent O2 (the approximate composition of air). Suppose water is saturated with the gas mixture at 25C and 1.00 atm total pressure,...
-
Crystal Clear Cleaning uses the allowance method to estimate bad debts. Consider the following January transactions for Crystal Clear: Jan. 1 Performed cleaning service for Debbie's D-list for $9,000...
-
Buerhle Company purchased (at a cost of $12,800) and used 3,300 kg of materials during May. Buerhle's standard cost of materials per unit produced is based on 2 kg per unit at a cost $4 per kilogram....
-
An experienced senior auditor was assigned to investigate a possible fraudulent situation characterized by extremely high, unexplained merchandise shortages at one location of the companys department...
-
The following data was prepared by the Waco Wagon Company. Required a. Under absorption costing, what is the unit product cost? b. Under variable costing, what is the unit product cost? c. Under...
-
2) In July 1960 the food wholesale firm of Hepplefinger & Company was expecting another problematic year of operations. For purposes of planning the firm's funds needs and to obtain a picture of the...
-
A randomized controlled trial comparing two drugs for treating insomnia is said to have 85% power to detect a 20% relative reduction (RR=0.80) in sleep problems nine months following treatment at the...
-
d S e evra la pre ve or we U PR GH (7 pts) AWA ROIT D'A OTTAWA TERIAL In the two-stage planetary gear train shown in the figure below, internal ring gear 6 is fixed and crank arms C and D are...
-
you design a bear spread using two put options : one with a strike price of x1=50 and a premium p1=3, and the other with the strike price of x2=75 and a premium p2=28. what is the initial cash flow?
-
Suppose a profit-maximizing firm with some market power in its output market has a production function with MPL = 15. The firm faces a marginal revenue (MR) function given by MR = 11-3* L. How much...
-
One of the terms that used to be used in middle adulthood was"midlife crisis", but we are finding this term used less and less. Articles like;...
-
Chris, a super salesman contemplating retirement on his fifty-fifth birthday, decides to create a fund on a 9% basis that will enable him to withdraw $45,000 per year on June 30, beginning in 2029...
-
You are comparing two banks. One bank is online and offers a savings account interest rate of 1.77% compounded quarterly. One bank is in your hometown and offers a savings account interest rate of...
-
content area top Part 1 Find the critical value z Subscript alpha divided by 2 that corresponds to the confidence level 84%. Question content area bottom Part 1 z Subscript alpha divided by 2equals...
-
Write a paper by answer the following question: Should Recycling Be Mandatory?
-
Distinguish between outsourcing, global sourcing, and offshoring.
-
William Corporation is a manufacturer of high quality mens and womens fashions. What steps should you take to transform William into a well recognized global brand?
-
Discuss the relationship between government intervention and protectionism.
-
Oxford Consulting, Inc., expects the following costs and expenses during the coming year: Required a. Compute a predetermined overhead rate applied on the basis of direct labor hours. b. Prepare a...
-
Dillon Manufacturing had the following inventories at December 31, 2018, the end of its fiscal year: During January 2019, the following transactions occurred; 1. Purchased materials on account,...
-
Job Cost Journal Entries Prior to the beginning of 2019, Stapleton Company estimated that it would incur \($153,000\) of manufacturing overhead cost during 2019, using 17,000 direct labor hours to...
Study smarter with the SolutionInn App