Find the resistance of a fiber with a crosssectional area of 1.34 mm 2 and length of
Question:
Find the resistance of a fiber with a crosssectional area of 1.34 mm2 and length of 10 cm that is subjected to a voltage of 225 V for which the current density is 1.25 A⁄cm2. Assume the resistor is uniform in material and properties.
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 50% (8 reviews)
Stone number is defined by the amount of an aggregate that will pass through specific sieves by ma...View the full answer
Answered By
Hardik Dudhat
I am semi-qualified Chemical Engineering ,I have scored centum in accounting in my senior secondary and in my graduation. I have always helped my fellow students with their concerns on the subject, i have tutored on various tutoring sites in the past and also have taken home tuitions for degree and MBA students. As a tutor, I don't want my students to just get a solution, I want them to understand the concept and never have a doubt in that area thereon and i believe in excelling and not in educating.
0.00
0 Reviews
10+ Question Solved
Related Book For
The Science And Engineering Of Materials
ISBN: 9781305076761
7th Edition
Authors: Donald R. Askeland, Wendelin J. Wright
Question Posted:
Students also viewed these Engineering questions
-
The crude copper that is subjected to electrorefining contains tellurium as an impurity. The standard reduction potential between tellurium and its lowest common oxidation state, Te4+, is Te4+(aq) +...
-
The manufacturer of a product that is subjected to repetitive cycles has specified that the product should be removed from service when any crack reaches 15% of the critical crack length required to...
-
The resistance of a platinum wire is to be calibrated for low-temperature measurements. A platinum wire with resistance 1.00 ' at 20.0C is immersed in liquid nitrogen at 77 K (-196C). If the...
-
If the arch rib \(A B C D E\) in Figure \(\mathrm{P} 6.30\) is to be funicular for the dead loads shown at the top joints, establish the elevation of the lower chord joints at \(B\) and \(D\). 40...
-
From what sources does a leader gain power? Which leadership style works best for a manager whose firm is making cost-cutting decisions? Why?
-
(a). Determine the ratio vo/is in the op amp circuit of Fig. 5.54. (b).Evaluate the ratio for R1 = 20 kΩ, R2 = 25 kΩ, R3 = 40 2kOmega$. ww R3 ww 10
-
\(3 \pi+7 \sqrt{21}=7 \sqrt{21}+3 \pi\) Identify the property of real numbers that is being illustrated.
-
At the time it defaulted on its interest payments and filed for bankruptcy, the McDaniel Mining Company had the following balance sheet (in thousands of dollars). The court, after trying...
-
Part A Step 1: Read the following scenario Wholesale Ltd acquired 80 per cent of the shares of House Construction Ltd on 30 June 2020 for a consideration of $800,000. The share capital and reserves...
-
Three ropes pull on a knot shown in (Figure 1) . The knot is not accelerating. A partially completed force diagram for the knot is shown in the figure (Figure 2) . Use Newton's second law to...
-
1. Calculate the resistivity of pure iridium at 673 K using its temperature resistivity coefficient. 2. Electrical conductivity is sometimes given in the units of %IACS. What does IACS stand for?...
-
A wire two microns in diameter is made from 10 cm silver, 0.1 cm gallium, and 10 cm silver all joined end to end (i.e., in series). Assume the joints are perfect and have no additional resistance....
-
Can you teach people to be ethical? How?
-
What is the As-Validated Configuration, and when is it established?
-
What is the Plug and Chug SDBTF paradigm? What are its origins? Why is it important to get the SDBTF Paradigm corrected in Engineering education?
-
What is the As-Produced Configuration, and when is it established?
-
What is an IBR and what is it intended to accomplish?
-
What is the As-Designed Configuration, and when is it established?
-
Did Tony weigh the range of political economic and operational uncertainties and risks when he took over AirAsia? What risks might he have overlooked?
-
Find the work done in pumping all the oil (density S = 50 pounds per cubic foot) over the edge of a cylindrical tank that stands on one of its bases. Assume that the radius of the base is 4 feet, the...
-
Refer to Figure 18.13. Given L 1 = 1.5 m, L 2 = 3 m; for the sand, ' = 33, = 16.5 kN/m 3 , sat = 19.0 kN/m 3 ; and, for the clay, c = 50 kN/m 2 , = 0, and sat = 20 kN/m 3 . Determine the depth of...
-
In a sandy soil (' = 35; = 18.0 kN/m 3 , and sat = 20.0 kN/m 3 ), the water table is located at a depth of 6 m below the ground level. How deep would you drive a sheet pile to carry out an...
-
The water table at a site is at 5 m below the ground level, and it is required to excavate to this level. The soil profile consists of a thick bed of sand where the unit weight is 17.0 kN/m 3 above...
-
Unit sales Contribution margin per unit Product X Product Y Product Z 2,000 $ 30 4,000 $ 20 4,000 $ 10 The average contribution margin for Company A is: Multiple Choice $18 per unit. $20 per unit....
-
When calculating earnings per share, a preferred dividend will affect the value of the numerator. True or false
-
In social responsibility reporting, the income statement bottom line is expanded to include financial, social and environmental performance, This standard is being only used in community government...
Study smarter with the SolutionInn App