What is the minimum Horizontal force F needed to make the box start moving in FIGURE 6-31?
Question:
31 N 25 kg
Step by Step Answer:
The static and kinetic friction forces each depend on ...View the full answer
Related Video
Static friction and kinetic friction are two types of friction that occur when two objects are in contact with each other. Static friction is the force that must be overcome to initiate motion between two surfaces that are in contact with each other but are not moving relative to each other. It is caused by the interlocking of rough surfaces at the microscopic level, and it increases as the force pushing the surfaces together increases. Once motion between the surfaces starts, the static friction is no longer present. Kinetic friction, also known as sliding friction, is the force that opposes the motion of two surfaces that are in contact with each other and are moving relative to each other. It is caused by the rubbing of the surfaces against each other and the resistance of the molecules in the surfaces to being moved. Kinetic friction is generally less than static friction, but it can still be a significant force, especially at high speeds. Both static and kinetic friction can be quantified using a coefficient of friction, which is a dimensionless number that represents the ratio of the frictional force between two surfaces to the normal force (the force perpendicular to the surfaces). The coefficient of static friction is typically greater than the coefficient of kinetic friction for a given pair of surfaces, because it takes more force to overcome the interlocking of the surfaces at rest than to maintain motion once it has started.
Students also viewed these Mechanics questions
-
A wood block of mass m rests on a larger wood block of mass M that rests on a wooden table. The coefficients of static and kinetic friction between all surfaces are s and k, respectively. What is the...
-
A 5-kg block is held at rest against a vertical wall by a horizontal force of 100 N. (a) What is the frictional force exerted by the wall on the block? (b) What is the minimum horizontal force needed...
-
For the cylinder in Problem 33, find the minimum horizontal force F that will roll the cylinder over the step if the cylinder does not slide on the corner.
-
4. What are the three categories of transactions in the balance of payments? Give an example of each. 5. Economists sometimes say that the current exchange rate system is a dirty float system. What...
-
The bracket is subjected to the two forces shown. Express each force in Cartesian vector form and then determine the resultant force FR. Find the magnitude and coordinate direction angles of the...
-
Discuss the five contemporary communication issues facing managers.
-
\(\sqrt{144}\) Identify which of the following are rational numbers.
-
The following information is available to assist you in preparing a bank reconciliation for Calico Corners on May 31, 2010: a. The balance on the May 31, 2010, bank statement is $8,432.11. b. Not...
-
PROBLEM 1 You were engaged to perform an audit of the accounts of the Fontana Blue Corporation for the year ended December 31, 2019 and have observed the taking of the physical inventory of the...
-
A manufacturer is considering alternatives for building new plants, to be located closer to three of its primary customers with whom it intends to develop long-term, sole-supplier relationships. The...
-
A car goes around a curve on a road that is banked at an angle of 21.5. Even though the road is slick, the car will stay on the road without any friction between its tires and the road when its speed...
-
Large ships often have circular structures in their windshields, as shown in FIGURE 6-59. What is their purpose? Called clear view screens, they consist of a glass disk that is rotated at high speed...
-
The part is to be milled, using a 20 mm diameter end mill with four teeth. Write the APT geometry and motion statements for this job. Assume that preliminary passes have been completed so that only...
-
Describe the role that marketing research plays at Dunkin' Donuts. What sort of information does Dunkin' Donuts consider when it's determining where to locate a new store? Discuss the importance of...
-
(a) First perform a multiple regression with all the variables, what can you say about the significance of the variables based on only the p-values. Next use the "step" function to perform backward...
-
After reading Hamblin's article, you'll notice he uses all three rhetorical appeals to change his reader's approach to sleep. write brief paragraph (5 sentences) identifying the ONE rhetorical appeal...
-
Delta-Gamma-Vega neutral. Q5. On MARCH 1, a portfolio manager expects a market down turn in the 5.1 5.2 next 4 months and decides to use the JUN puts on the S&P500 index in order to protect the...
-
Discuss how ICT can create value in your business. Consider the various matters that might have impacted the existing ICT system during Covid-19 in the light of the case study. KPMG. (2022). KPMG...
-
The vector OA(vector) has a magnitude of 25 units and is parallel to the vector -3i + 4j. The vector OB(vector) has a magnitude of 26 units and is parallel to the vector 12i + 5j. Find: a. OA(vector)...
-
What tools are available to help shoppers compare prices, features, and values and check other shoppers opinions?
-
A thin-walled pipe rolls along the floor. What is the ratio of its translational kinetic energy to its rotational kinetic energy about the central axis parallel to its length?
-
A solid sphere of weight 36.0 N rolls up an incline at an angle of 30.0. At the bottom of the incline the center of mass of the sphere has a translational speed of 4.90 m/s. (a) What is the kinetic...
-
An automobile has a total mass of 1700 kg. It accelerates from rest to 40 km/h in 10 s. Assume each wheel is a uniform 32 kg disk. Find, for the end of the 10 s interval, (a) The rotational kinetic...
-
1) What is the system and service manager on our Fedora VMs?How can you verify that on your system? (show the command below).What version of Linux is running on fawad, and what is it's system...
-
7)The terminal value is always "placed" in the last year of a DCF forecast. If the terminal value is placed in year 2024 (as it is in Case 2, for P&G), this value represents...
-
Question 1 Not yet answered Marked out of 1.00 Flag question Select the two published documents that provide requirements, specifications and guidelines relating to corporate sustainability. Select...
Study smarter with the SolutionInn App