Question: A 20-kip load is carried by the crane hook shown in the figure. The cross section of the hook uses two concave flanks. The width

A 20-kip load is carried by the crane hook shown in the figure. The cross section of the hook uses two concave flanks. The width of the cross section is given by b = 2/r, where r is the radius from the center. The inside radius ri is 2 in, and the outside radius ro = 6 in. Find the stresses at the inner and outer surfaces at the critical section.

Step by Step Solution

★★★★★

3.47 Rating (147 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

2 A bdr f dr 2 in 2 2197225 in 7 rc In i 2 2197225 br dr 20 000 2197 1 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

M-E-L-E (69).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

For the crane hook shown in Figure P11-16, determine the largest displacement and the maximum von Mises stress and where this value is located on the hook. Use AISI 4130 steel with yield strength of...

Figure shows a ring of outer radius R = 13.0 cm, inner radius r = 0.200R, and uniform surface charge density = 6.20pC/m2. With V - 0 at infinity, find the electric potential at point P on the...

Figure shows a cross section of a long thin ribbon of width w = 491 cm that is carrying a uniformly distributed total current i = 4.67A into the page. In unit-vector notation, what is the magnetic...

1. A crane hook is to be designed to carry a load F as shown in the Figure Q2.1 below B A To F I R- To B n T1 Cross section AB Figure Q2.1: Crane hook The hook can be modeled as a three-quarter...

b . Use ASD. 3 . 7 - 2 A W 1 4 4 8 is supported by two tension rods A B and C D , as shown in Figure P 3 . 7 - 2 . The 2 0 - kip load is a service live load. Use load and resist - ance factor design...

Problem # 1 ( 3 0 pts ) : Given: Reinforced concrete beams are composed of both concrete ( strong in compression ) , and steel ( equally strong in both compression and tension ) . Your company needs...

Statically Indeterminant Deflection in Beams Problem 1 : Setup: The beam is used to support the 2 0 - kip load. Assume A is fixed and B is a roller. Find: Determine the reactions at the supports. ? 1...

6. Which of the following are functions of bearings? (a) Ensure free rotation of shaft with minimum friction (b) Holding shaft in a correct position (c) Transmit the force of the shaft to the frame...

MAINLY FIND PARTS B and C and show work, answers given ( adapted from Hibbeler 1 0 t h ed . prob. 1 2 - 1 2 1 ) A 2 0 - kip load is supported by an A 3 6 steel, W 1 6 x 2 6 beam as shown. Assume A is...

( adapted from Hibbeler 1 0 t h ed . prob. 1 2 - 1 2 1 ) A 2 0 - kip load is supported by an A 3 6 steel, W 1 6 \ times 2 6 beam as shown. Assume A is rigidly fixed and B behaves as a roller....

An aluminum wire (=2.65 x 10 -8 m) has a length of 20.0 meters and a diameter of 2.00mm. What is the resistance of this wire? a) 0.0845 b) 0.530 c) 2.12 d) 0.169

For the data of Problem 13.85, repeat (a) through (g), using Growth as the independent variable.

What is the eight - hour exposure value referred to in OSHA standard 2 9 CFR 1 9 1 0 . 1 0 0 0 ? A . time weighted average ( TWA ) B . short - term exposure limit ( STEL ) C . permissible exposure...

The Stevenson college has a 2,900 dollar balance to pay in the subsidiary ledger. The allowance for doubtful accounts has a credit balance of 1750.81 in the general ledger. There is a 0 dollar debit...

According to the case above, advise Mr. Doolittle as to whether the expenses incurred in the United Kingdom would be deductible for income tax purposes? You are a chartered tax accountant working in...

Mark from Marks Mowers wants to make some changes to his business. He has asked each of his department managers (Production, Marketing and Sales) to submit a plan for growth to you the General...

The shaft shown in the figure is supported by two bearings and carries two V-belt sheaves. The tensions in the belts exert horizontal forces on the shaft, tending to bend it in the X-Z plane. Sheave...

Two cylindrical pressure vessels made of the same unidirectional lamina but with different fiber orientations were loaded as shown in Fig. P4.43 gave the following strain readings. Cylinder A...

Video Solution Consider the following cash flow profile and assume MARR is 10%/yr. a. What does Descartes rule of signs tell us about the IRR(s) of this project? b. What does Norstroms criterion tell...

Fill out the blue table on the bottom-right of the file , thank you so much. Microsoft Excel 16.0 Sensitivity Report Worksheet: [MSW Assignment 1 Key Sp2021.xlsx]Sheet1 Report Created: 4/1/2021...

Chapter 3 Assignment Back to Assignment Attempts Score/1 4. Pure expectations theory: Three-year bonds 79:12 Larry would like to invest a certain amount of money for three years and considers...

Filer Manufacturing has 7 million shares of common stock outstanding. The current share price is $86, and the book value per share is $5. Filer Manufacturing also has two bond issues outstanding. The...