Question: An end milling operation is performed on an NC machining center. The total length of travel is 625 mm along a straight line path to

An end milling operation is performed on an NC machining center. The total length of travel is 625 mm along a straight line path to cut a particular work piece. Cutting speed = 2.0 m/s and chip load (feed/tooth) = 0.075 mm. The end milling cutter has two teeth and its diameter = 15.0 mm. Determine the feed rate and time to complete the cut.

Step by Step Solution

★★★★★

3.40 Rating (166 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

N 25465 revmin ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (477).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

In the S/370 architecture, a storage key is a control field associated with each page-sized frame of real memory. Two bits of that key that are relevant for page replacement are the reference bit and...

A milling operation is performed on a NC machining center. Total travel distance = 300 mm in a direction parallel to one of the axes of the worktable. Cutting speed = 1.25 m/s and chip load = 0.05...

The outline of the cam in Figure P7.38 is to be machined in an end milling operation, using a 12.5 mm diameter end mill with two teeth. The part is 7.5 mm thick. Write the complete APT program for...

The experimental result differs from the assumption. The result shows that the ring oscillator frequencies can be grouped into two groups, where the first group is the high frequency group for the...

E-Physics Tutorial Book Note: I have attached below the lesson for the 3 activities. Thank you so much for your time and effort. Activity 1. Directions: Use the right-hand rule to determine the...

ITEM #1 LEARNING FROM THE HEADLINES True to the Learning from the Headlines approach of this course, watch the Part Three Intro Video after you read the short article the video highlights. Notice...

Project Management Casebook David I. Cleland, Karen M. Bursic, Richard Puerzer, and A. Yaroslav Vlasak Library of Congress Cataloging-in-PublicationData Project management casebook /edited by David...

Chapter Ten Nonwage Issues in Bargaining Wage and nonwage issues are not completely separable. Both have economic consequences for the employer. For example, provisions relating to hours of work...

This is your week 4 paper for HRMT413. READ FULLY CHAPTER 10 OF YOUR TEXT: 4 page paper Consider your current or any former work location at which you have been employed. In a power point or word...

Define the term entrepreneurship.

According to a new study released by Infosys, a global leader in consulting, outsourcing and technology, more than three quarters (77%) of U.S. consumers say that banking on their mobile device is...

An unlawful killing that is missing the malice aforethought is

In an experiment, are the responses an independent variable or a dependent variable?

Give the firing sequence for the Petri net of Fig. 3-23 corresponding to the state sequence (000), (01A), (01), (010), (01A) in Fig. 3-21. Explain in words what the sequence represents.

Given the transition rules AC B, B AC, CD E, and ECD, draw the Petri net described. From the Petri net, draw the finite state graph reachable from the initial state ACD. What well-known concept do...

PPP is based closely on HDLC, which uses bit stuffing to prevent accidental flag bytes within the payload from causing confusion. Give at least one reason why PPP uses byte stuffing instead.

THE ANSWER IS NOT 4.92% I ALREADY SUBMITTED THAT AND IT WAS NOT CORRECT. The Cullumber Products Co. currently has debt with a market value of $300 million outstanding. The debt consists of 9 percent...

The operating profit benchmarks on p.6 of each issue of the GLO-BUS Statistical Review showing the industry-low: industry-average, and industry-high values for operating profit per camera sold in...

OpenSeas, Inc. is evaluating the purchase of a new cruise ship. The ship will cost $505 million, and will operate for 20 years. OpenSeas expects annual cash flows from operating the ship to be $68.6...