Question: Consider the blending system of Exercise 102. Inlet how rate, w2, and the bypass fraction, f, can be manipulated. Determine the model degrees of freedom,

Consider the blending system of Exercise 102. Inlet how rate, w2, and the bypass fraction, f, can be manipulated. Determine the model degrees of freedom, NF, and the control degrees of freedom, NFC.

Step by Step Solution

★★★★★

3.29 Rating (170 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The dynamic model consists of the following material balances Mass ba... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

38-E-C-E-P-C (149).docx

120 KBs Word File

Students Have Also Explored These Related Chemical Engineering Questions!

Consider the blending system shown in Figure. A feedback control system is used to reduce the effect of disturbances in feed composition, x 1 , n the controlled variable, product composition, x....

Consider the fraction nonconforming control chart in Exercise 6.5. Find the equivalent npchart. Lot Number of Lot Number of 230 435 221 346 230 327 285 311 342 308 12 13 14 15 16 17 18 19 20 456 394...

How many numbers of degrees of freedom does an F-curve have? What are those degrees of freedom called? Why do you think they are so called?

I want to answer the questions in the attached picture in the picture you can find a title called (Questions) , I need to solve all four questions mentioned below this title 1. Use MATLAB Version...

A stirred-tank heat exchanger with a bypass stream is shown in Fig. E. with the available control valves. The possible manipulated variables are: mass flow rate w 2 , valve stem positions x c and x 3...

I want an answer for all four questions in the attached file Notes: 1. Use MATLAB Version R2013b 2. Labs containing MATLAB: E1-S04 and E2-F09 Read the problem statement below before attempting to...

2. Discuss the exception to the general rule that contract entered by minor is void 2. Discuss the exception to the general rule that contract entered by minor is void.

413-432_CH18_Nachmias.qxd 1/17/07 3:47 PM Page 413 Chapter Index Construction and Scaling Methods INDEX CONSTRUCTION The Purpose of the Index The Sources of the Data The Base of Comparison Methods of...

Factors affecting people without estate planning around middle class black females in South Africa Inforgraphic..

Oscar Ltd manufactures small electrical parts in Hamburg, Germany. The company has a production capacity of 18,000 electrical units per year and the unit cost is as follows: The companys accountant...

The histogram shows frequencies for the ages of 25 CEOs listed at Forbes.com. Convert this histogram to one showing relative frequencies by relabeling the vertical axis, with the appropriate relative...

1.What is Apache Kafka and how does it work?

An incomplete subsidiary ledger of materials inventory for May is as follows: RECEIVED ISSUED BALANCE Receiving Materials Report Unit Requisition Unit Number Quantity Price Number Quantity Amount...

sin a cos a 16. sin a cos a - = 1+ sin a COs a

The following selected accounts appear in the ledger of Parks Construction Inc. at the beginning of the current year: Preferred 2% Stock, $100 par (100,000 shares authorized, 80,000 shares issued)...

(Q3-A) Choose the correct answer for eight only 1-Two hollow balls made of (a- Steel and b- Aluminum) both have the same dimension and were floating in water, the buoyancy force was A) Greater in the...

CSc a + sec a tan a 14. tan a sec a csc2 a

The Ka of acetic acid, CH 3 COOH, is 1.8 10 5 . Calculate the pH of a 0.10 M acetic acid solution. Strategy We begin as usual, by setting up an equilibrium table and determining the concentrations...

The shaft shown in the figure carries a 20-lbf gear on the left and a 35-lbf gear on the right. Estimate the first critical speed due to the loads, the shafts critical speed without the loads, and...

A transverse drilled and reamed hole can be used in a solid shaft to hold a pin that locates and holds a mechanical element, such as the hub of a gear, in axial position, and allows for the...

A guide pin is required to align the assembly of a two-part fixture. The nominal size of the pin is 15 mm. Make the dimensional decisions for a 15-mm basic size locational clearance fit.

You work for a nuclear research laboratory that is contemplating leasing a diagnostic scanner ( leasing is a common practice with expensive, high - tech equipment ) . The scanner costs $ 4 , 9 0 0 ,...

-You have contacted a number of car dealerships to determine the best interest rate on a new automobile loan. A Ford dealership has quoted you a 5-year, 10% loan in the amount of $35,000 that will...

Harry, Tamara, and Lana were partners under a written agreement made in February that the partnership should continue for ten years. During the same year, Lana, being indebted to Jones, sold and...