Question: Referring back to Problem 7.8, the mechanical inaccuracies in the open loop positioning system can be described by a normal distribution whose standard deviation =

Referring back to Problem 7.8, the mechanical inaccuracies in the open loop positioning system can be described by a normal distribution whose standard deviation = 0.005 mm. The range of the worktable axis is 500 mm, and there are 12 bits in the binary register used by the digital controller to store the programmed position. For the positioning system, determine

Step by Step Solution

★★★★★

3.53 Rating (174 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a CR 1 p n s 4 mm250 0016 mm CR 2 0122 mm CR Max CR 1 CR 2 Max0016 0122 0122 mm ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (470).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

A TLR robot has a rotational joint (type R) whose output link is connected to the wrist assembly. Considering the design of this joint only, the output link is 600 mm long, and the total range of...

Referring back to the searching problem (see Exercise 2.1-3), observe that if the sequence A is sorted, we can check the midpoint of the sequence against v and eliminate half of the sequence from...

Consider the torsional mechanical system in Figure CP4.7(a). The torque due to the twisting of the shaft is -kÎ¸; the damping torque due to the braking device is -bÎ¸; the...

An open - loop positioning system uses a stepper motor connected to a ball screw with a 4 : 1 gear reduction ( four turns of the motor for each turn of the ball screw ) . The stepper motor has a step...

2 Suppose the mechanical inaccuracies in the open loop positioning system of Example 7 . 1 are described by a normal distribution with standard deviation = 0 . 0 0 6 mm . The range of the worktable...

The Picture is the example the problem is talking about 2. Suppose the mechanical inaccuracies in the open-loop positioning system of Example 7.1 are described by a normal distribution with standard...

15. Suppose the mechanical inaccuracies in the open-loop positioning system of Example 7.1 are described by a normal distribution with standard deviation = 0.006 mm. The range of the worktable axis...

Set Student Name: 1. Answer true or false for each part, and if false, explain your answer. a. The point estimate for the population mean, , of an x distribution is x-bar, computed from a random...

Instuctor's Annotated Edition TENTH EDITION Understandable Statistics Concepts and Methods Charles Henry Brase Regis University Corrinne Pellillo Brase Arapahoe Community College Australia Brazil...

Select an organisation with which you are familiar and write a report on how you would transform a clearly defined segment of the organisation into a sustainable business segment. Do not select an...

The group project is a hands-on exercise in planning a financial statement audit. The project will give you an opportunity to consider how the concepts and techniques discussed in the course apply in...

Test the vulnerability of a machine at the following site: grc.com/default.htm. Follow the ShieldsUP! link for a series of free tests listed midway down the page.

3 . 4 Part 1 of 2 Find the slope and y - intercept of the line. x + y = 1 4

Briefly describe an informal experiment that you or someone you know recently conducted. Were there alternative explanations for the responses you observed?

A block of bits with n rows and k columns uses horizontal and vertical parity bits for error detection. Suppose that exactly 4 bits are inverted due to transmission errors. Derive an expression for...

What is the remainder obtained by dividing x7 + x5 + 1 by the generator polynomial x3 + 1?

A bit stream 10011101 is transmitted using the standard CRC method described in the text. The generator polynomial is x3 + 1. Show the actual bit string transmitted. Suppose the third bit from the...

You are examining a company's balance sheet and find that it has total assets of $ 1 9 , 9 8 8 , a cash balance of $ 1 , 9 9 2 , inventory of $ 4 , 6 5 7 , current liabilities of $ 5 , 3 1 7 , and...

Estimating the cash flow generated by $1 invested in a project The profitability index (PI) is a capital budgeting tool that is defined as the present value of a project's cash inflows divided by the...

Business will have a fixed costs of $750,000 per year. It plans on selling one product that will have a variable cost of $20 per unit. What is the products selling price to break-even? Values Selling...