Question: Repeat Prob. 357 with an allowable shear stress of 20 kpsi and a power of 50 hp. Repeat Prob. 357, Using a maximum allowable shear

Repeat Prob. 3–57 with an allowable shear stress of 20 kpsi and a power of 50 hp.
Repeat Prob. 3–57, Using a maximum allowable shear stress of 70 MPa, find the shaft diameter needed to transmit 40 kW when
(a) The shaft speed is 2500 rev/min.
(b) The shaft speed is 250 rev/min.

Step by Step Solution

★★★★★

3.31 Rating (163 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a b Obtain the torque from the g... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

233-M-E-L-E (126).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The steel step shaft has an allowable shear stress of Ï allow = 8 MPa. If the transition between the cross sections has a radius r = 4 mm, determine the maximum torque T that can be applied. 50...

The wood beam has an allowable shear stress of Ï allow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section. 50 mm 50 mm +100 mm- 50 mm 200 mm 50 mm

Using a maximum allowable shear stress of 70 MPa, find the shaft diameter needed to transmit 40 kW when (a) The shaft speed is 2500 rev/min. (b) The shaft speed is 250 rev/min.

Problem 4 ( Textbook 3 - 5 7 ) Using a maximum allowable shear stress of 7 0 MPa , find the shaft diameter needed to transmit 4 0 kW when ( a ) The shaft speed is 2 5 0 0 r e v m i n . ( b ) The...

3-1C W hat is the difference between saturated liquid and compressed liquid? 3-2C What is the difference between saturated vapor and superheated vapor? 3-3C Is there any difference between the...

Need solutions for solving 4.4 and 4.8 using python. Questions are attached as a screenshot. and a centered dallerence approximation o O) to estimate the first derivative of the function examined in...

i need a matlab code to plot both the input and output signals for the question 6.2-6 ( figure 2.8-4(b) ) 6.2-4 A message signal m(r) is normalized to peak voltages of 1 V. The average message power...

Chap. 6 Problems 1 7 3 6 - 8 . Repeat Prob. 6 - 7 using the moment forces at joints b , c , and d as the redundants. 6 - 9 . Analyze the truss in Fig. 6 - 3 8 by the method of consistent...

.Use MATLAB to solve 18.17 p524 Write your name and ID inside the program code, or it will be considered .sheeting Submit both the source code and the .output 524 INTERPOLATION PROBLEMS y 18.1...

6 - 1 0 . Analyze each of the trusses in Fig. 6 - 3 9 by the method of consistent deformations. Assume that E = 3 0 , 0 0 0 kip s i n 2 ? 2 and in . ( : ? 2 } for all members. 6 - 1 1 . Analyze the...

Which population numbers do you trust to be closer to the actual pop- ulation size, the values obtained during sonar surveys or visual sur- 3. veys? Explain.

How are indicators and indexes used in judgmental forecasting?

Do the CAFO regulations a particular state has in place affect whether CAFO investors site there?

When might optimism become a detriment to a leader?

List and briefly explain the three mechanisms by which metals shrink during casting.

Sketch the microstructure you would expect for a slab cast through (a) Continuous casting, (b) Strip casting, (c) Melt spinning.

The general design recommendations for a well in sand casting are that (a) Its diameter should be twice the sprue exit diameter, and (b) The depth should be approximately twice the depth of the...

If the interest rates on all bonds rise from 5 to 6 percent over the course of the year, which bond would you prefer to have been holding? Consider a one - year holding period. A bond with twenty...

Problem 4-25 Complete cosh budget [LO4-2] Harry's Carryout Stores has eight locations The firm wishes to expand by two more stores and needs a bank loan to do this Mr Wilson, the banket will finance...

Question 12 Use PMT = to determine the regular payment amount, rounded to the nearest dollar. The price of a home is $300,000. The bank requires a 20% down payment. After the down payment, the...