Question: A source of sinusoidal emf with constant voltage is connected in series with an oscillating circuit with quality factor Q = 100. At a certain

A source of sinusoidal emf with constant voltage is connected in series with an oscillating circuit with quality factor Q = 100. At a certain frequency of the external voltage the heat power generated in the circuit reaches the maximum value. How much (in per cent) should this frequency be shifted to decrease the power generated n = 2.0 times?

Step by Step Solution

★★★★★

3.40 Rating (159 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

VR R XLXc At resonance XXc wo VLC Power generated will decrease n tim... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

P-O-E-O (47).docx

120 KBs Word File

Students Have Also Explored These Related Oscillations Mechanical Waves Questions!

A 185-pF capacitor is connected in series with an unknown capacitance, and as a series combination they are connected to a battery with and emf of 25.0 V. If the 185-pF capacitor stores 125pC of...

A 3.0-M resistor is connected in series with an initially uncharged 0.28-F capacitor. This arrangement is then connected across four 1.5-V batteries (also in series). (a) What is the maximum current...

A 175-pF capacitor is connected in series with an unknown capacitor, and as a series combination they are connected to a 25.0-V battery. If the 175-pF capacitor stores 125 pC of charge on its plates,...

If it is low, the wave reflected back up the tower will largely remove the potential existing due to the incident wave. In this way the chance of flashover is eliminated. If, on the other hand, the...

This streamer is very intense where the current varies between 1000 amps and 200,000 amps and the speed is about 10% that of light. With a particular number of towers the chances of incidence of...

It is, therefore, desired that for good line design high surge impedances in the ground wire circuits, the tower structures and the tower footing should be avoided. High saturation induction (to...

Name: Grade and Section: Score: School: Teacher: Subject: General Physics 2 LAS Writer: JEREMIAH S. SABRIDO Content Evaluator: RETCHIE JOY PISANA, MICHAEL DAVE NALAGON Lesson Topic: Electromotive...

The sensitivity of a relay refers to the smallest value of the actuating quantity at which the relay operates detecting any abnormal condition. In case of an over current relay, mathematically this...

A group of dc motors is to operate at 220 volts at a place that is 400 ft away from 230-volt mains. What diameter (minimum) of copper wire is to be used in connecting the motors to the main, if the...

In case of an over current relay, mathematically this can be defined as the ratio between the short circuit fault current (Is) and The relay operating current (Io). The value of Io should not be too...

A fixed asset with a cost of $41,000 and accumulated depreciation of $36,000 is traded for a similar asset priced at $50,000. Assuming a trade-in allowance of $4,000, what is the cost basis of the...

Refer to Practice 19-1 and Practice 19-2. What would be the impact on the companys total cash payment in Year 2 if the pay-fixed, receive-variable interest rate swap had been based on a loan amount...

Take Exam: AUE 6 D 2 : Question 2 6 of 3 0 Instant - start lamps require single - pin bases and are generally called A ) U - shaped tubes B ) slimline lamps C ) dimmers D ) preheats

You are an accountant in the budgetary, projections, and special projects department of American Conductor, Inc., a large manufacturing company. The president, William Brown, asks you on very short...

The Welding Department of Batista Manufacturing Company has the following production and manufacturing cost data for February 2010. All materials are added at the beginning of the process....

The Sanding Department of Ortiz Furniture Company has the following production and manufacturing cost data for March 2010, the first month of operation. Production: 12,000 units finished and...

Podsednik Company has gathered the following information Units in beginning work in process ..............0 Units started into production ..................36,000 Units in ending work in process...

Find the tension in the two cords shown in Fig. 9-45. Neglect the mass of the cords, and assume that the angle θ is 33o and the mass m is 170 kg.

Several factors influence the location and arrangement of materials in astoreroom or warehouse. What factor(s) are regarded as most important?13. What is the key to controlling finished goods...

Requirement 1. Use the EOQ model to determine the optimal number of pairs of shoes per order. Begin by selecting the formula used to calculate EOQ. ( D= Demand in units for one year, P= Ordering cost...

Two firms, No Leverage Inc. and High Leverage Inc. have equal levels of operating risk and differ only in their capital structure. No Leverage is unlevered and High Leverage has $ 5 0 0 , 0 0 0 of...

A bank has decided to set its interest rates to compound monthly on all deposits in order to give customers the same benefits as its current offering of 3.39% compounded quarterly. At what value...