Question: For the system of Figure P2.12 find the transfer function, G(s) = X 1 (s)/F(s). K = 4 N/m -Xj K, = 5 N/m ft)

For the system of Figure P2.12 find the transfer function, G(s) = X1(s)/F(s).

K = 4 N/m -Xj K, = 5 N/m ft) = 3

K = 4 N/m -Xj K, = 5 N/m ft) = 3 N-s/mM1 =T'kg Jv2=3N-s/m M2 = 2 kg fva = 2 N-s/m %3D FIGURE P2.12

Step by Step Solution

★★★★★

3.29 Rating (170 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Gs X1s M1k1 ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Control Systems Engineering Questions!

Q:

For the system of figure below find the transfer function G(s)=X 1 (s)/F(s). K1 = 4 N/m K2 = 5 N/m f(t) fy, = 3 N-s/m M =Ikg Jv2=3N-s/m M,= 2 kg fva = 2 N-s/m! %3D

Q:

Consider the DC motor control system with rate feedback shown in Figure below. DC Motor Control System +51 +255 000,0 s(1 5) 8,0 Kp I K ks s(1+5) 1+k's (b) Figure 1: DC motor control system Image by...

Q:

The system of Figure CDP4.1 uses a controller Gc (s) = K0. Determine the value of Ku so that the phase margin is 70. Plot the response of this system to a step input.

Q:

Find the Transfer Function model of the dynamic system in Figure 2.49. K = 2 N/m 0000 (t) K = 5 N/m -x(1) 0000 f(t) fv = 1 N-s/m M =1 kg fv = 1 N-s/m M2=2 kg fv32 N-s/m Figure 2.49 Dynamic system.

Q:

Find the transfer function, X 3 (s)/F(s), for each system shown in Figure P2.14. 13() fv = 4 N-s/mp K= 5 N/m fv = 4N-s/m f()- M, = 4 kg0000 M2 = 4 kg fvz = 4 N-s/m fv=4 N-s/m (a) X(1) Frictionless 1...

Q:

A linear DC machine is an electromechanical system shown in the following figure. When the switch is closed the bar starts to move on the right side. 1. Determine the transfer function G (s) = X(s)...

Q:

Please show the MATLAB coding for the Lab portion. Skill-Assessment Exercise 3.2 PROBLEM: Represent the translational mechanical system shown in Figure 3.9 in state space, where x3(t) is the output....

Q:

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

Q:

MATHEMATICS FOR MACHINE LEARNING Marc Peter Deisenroth A. Aldo Faisal Cheng Soon Ong Contents Foreword 1 Part I Mathematical Foundations 9 1 Introduction and Motivation 11 1.1 Finding Words for...

Q:

Planning Demand and Supply in a Supply Chain Capacity Planning and Assignment 1 utdallas.edu/~metin Outline Capacity Planning Product-to-plant Assignment utdallas.edu/~metin 2 Deterministic Capacity...

Q:

Client Phil Collins Realty Corporation purchased a tract of unimproved land for $55,000 This land was improved and subdivided into building lots at an additional cost of $34,460 These building lots...

Q:

Using the information gained in the article by Gretchen Morgenson, How the Thundering Herd Faltered and Fell, draft a memo applying the ERM framework to identify the excessive risk taken by Merrill...

Q:

The vertices of AABC are at A(-1,-3), B(2, 3) and C(k + 5,k) Find the value of k if AB is perpendicular to BC

Q:

Look back at this chapters A Case for Complexity. Where in this case can you see evidence of emergence, self-organization, adaptability, independent agents, and distributed leadership? Describe...

Q:

Cable AB on the boom truck is hoisting the 2500-lb section of precast concrete (Figure P4.18). A second cable is under tension P, and workers use it to pull and adjust the position of the concrete...

Q:

Solve the problem of Example 4.5 by using the force components method. Replace the polar representation of the anchor straps tension by the horizontal and vertical components T x and T y , and solve...

Q:

A front loader of mass 4.5 Mg is shown in side view as it lifts a 0.75-Mg load of gravel (Figure P4.20). (a) Draw a free body diagram of the front loader. (b) Determine the contact forces between the...

Q:

1 SECTION A (COMPULSORY QUESTION) QUESTION ONE Ama Amelicans Groups PLC holds a subsidiary company called DontTell Limited. DontTell Limited, is based in Zambia and has commenced production of a...

Q:

The following is information for Sarasota Corp. for the year ended December 31, 2020: $1,410,000 Loss on inventory due to decline in net realizable value $84,000 Sales revenue Unrealized gain on...

Q:

Business 100 QUESTION 26 The North American Free Trade Agreement regulates trade between the United States, Canada, and Japan. True False QUESTION 27 South Africa produces diamonds more cheaply and...