Question: An Otto cycle engine has a total displacement of 0.0040 m3. Its compression ratio is 9.0. It is fueled with gasoline having a specific heating

An Otto cycle engine has a total displacement of 0.0040 m3. Its compression ratio is 9.0. It is fueled with gasoline having a specific heating value of 45,500 kJ/kg. Its mass air-to-fuel ratio is 16.0. Assume the density of air is 1.00 kg/m3. Determine its ideal power output at N = 4.00 × 10³ RPM, in kW and in HP. (A: 2.2 × 10² kW, 3.0 × 10² HP (kg air)/(kg fuel))

Step by Step Solution

★★★★★

3.37 Rating (163 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The ideal power output of an Otto cycle engine can be ca... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Exploring Engineering Introduction Questions!

The irreversible gas-phase reaction Acat B is carried out adiabatically over a packed bed of solid catalyst particles. The reaction is first order in the concentration of A on the catalyst surface...

What would be the Otto cycle efficiency in Example 6.1 if the engines compression ratio was 10.0? Example 6.1 A new four-cylinder Otto cycle engine has a total displacement of 5000. cm 3 and a...

What would be the ideal power produced in Example 6.1 if the engines total displacement was 8000. cm 3 and it was running at 3000. RPM? Example 6.1 A new four-cylinder Otto cycle engine has a total...

Suppose you wanted to design an Otto cycle engine with the same power output as the two jet engines powering the fire truck. Suppose your Otto cycle engine was able to achieve the far higher...

A 3 - L V 6 engine operates at 2 4 0 0 RPM with a mechanical efficiency of 8 4 % . Cylinder conditions at the start of compression in an SI engine operating at WOT on an air - standard Otto cycle are...

Question 1 A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement. The fluids mix with each other in an open...

This homework set allows you to evaluate an open system analysis of an idealized engine. An inventor has proposed a modern manifestation of an Atkinson cycle engine concept to control engine load...

The temperature at the end of combustion in an Otto cycle is 2200 K. The excess air coefficient is 1.2. The fuel used is gasoline (C7.76H13.1). Calculate the volume percentages of CO2, H2O, O2 and N2...

3. Answer the following questions relating to heat engines: a) Describe and illustrate in detail the complete Otto cycle including all the thermodynamic processes involved. Include the pV diagram....

Question 1 a ) Derive the air standard efficiency of an ideal Otto cycle in terms of volume compression ratio and the ratio of specific heat capacities for air, f r o m first principles. State your...

Automotive Thermodynamics A Volkswagen Passat has a six-cylinder Otto cycle engine with compression ratio r = 10.6. The diameter of each cylinder, called the bore of the engine, is 82.5 mm. The...

Jack Warren lives in Invercargill and has recently joined the staff of his community hospital as the financial controller. He is also a member of the Hospital Foundation that runs several very...

Lynn Benedict, the bookkeeper for New York Company, has been trying to get the balance sheet to balance InstructionsExplain to Lynn Benedict in a memo why the original balance sheet is incorrect, and...

Which financing option involves using a third party for payment processing? Group of answer choices Open account. Documentary collection. Letter of credit. Consignment.

What excited you most about starting the venture?

The spur gear has a pitch radius of 2.5 in. (Figure P4.12). During a geartrains operation, a 200-lb meshing force acts at 25 relative to horizontal. Determine the moment of that force about the...

Determine the moment of the 35-lb force about the center A of the hex nut (Figure P4.13). Figure P4.13 6 in. 24 in. 20 H 35 lb

Two construction workers pull on the control lever of a frozen valve (Figure P4.14). The lever connects to the valves stem through the key that fits into partial square grooves on the shaft and...

Help me with this thanks Four logistic regression models are fitted to a data set in R using the following code: fitl

Today, a US firm agrees to buy merchandise from Mexico worth 12 million Mexican pesos. The merchandise will be delivered in 60 days with payment to be made in 90 days {that is, 30 days after the...

1. [Maximum mark: 5] The following diagram shows triangle ABC, with AB = 6 and AC = 8. diagram not to scale B 6 A C 8 (a) Given that cos A = alu , find the value of sin A. [3] (b) Find the area of...