Question: Suppose gear A was driven by a motor at 1800. RPM. Suggest an arrangement of gears from the given gear set A, B, and C

Suppose gear A was driven by a motor at 1800. RPM. Suggest an arrangement of gears from the given gear set A, B, and C to achieve an output speed of 18,900 RPM.

Concern a gear set consisting of up to the three gears as shown here. In each case the larger (36 or 42 tooth) and smaller (12 tooth) portions of each gear are fastened together so that they rotate at the same rate.

42 Teeth 42 Teeth 36 Teeth A 12 Teeth 12 Teeth 12 Teeth B.

Step by Step Solution

★★★★★

3.43 Rating (159 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

We have to solve this problem by trial error method We have to find gear train which gives train val... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Exploring Engineering Introduction Questions!

1. A pulley of diameter 14.0 cm is driven by an electric motor to revolve 75.0 rpm. The pulley drives a second one of diameter 10.0 cm. How many revolutions does the second pulley make in 1.00 min?...

1. A driver gear has 36 teeth and makes 85.0 rpm. Find the rpm of the driven gear with 72 teeth. 2. A motor turning at 1250 rpm is fitted with a gear having 54 teeth. Find the speed of the driven...

1. A driver gear has 72 teeth and makes 162 rpm. Find the rpm of the driven gear with 81 teeth. 2. A driver gear with 60 teeth makes 1600 rpm. How many teeth must the driven gear have if it makes 480...

4 . A gear box is designed to transmit power across one axis to the other at an angle of 9 0 degree. To have a large speed reduction ratio, we use a worm gear drive for a driving shaft rotating at 2...

For this project, students will design a two - stage reverted spur gear speed reducer to accommodate a reduction in speed from 1 8 0 0 rpm ( gear 2 ) at the input shaft ( driven directly by an...

IBL ( Chapter 1 4 - covered using problem based learning method ) ME 3 0 2 - Machine Design IIGear Design Chapters 1 3 and 1 4 , from textbookProblem StatementThe Figure 1 below shows an electric...

Problem #1 [40 pts] For the shown worm-gear set (figure 1), the designer is proposing to change the type of bearings used for supporting the worm shaft to two identical tapered roller bearings;...

The hoisting rope of a gantry crane is required to lift a load at a speed of 4.25 m/min. The drum on which the rope is wound is driven by a motor via a gearbox. The drum diameter is 650 mm and the...

Consider the reverted compound helical gear train shown with the given numbers of teeth. The normal module of Gear 1 is 3.5 mm and the normal module of Gear 3 is 5 mm. Gear 1 has left-hand helix and...

Task 1: Pulley Size The machine has a motor which runs at a speed of 1725 rpm and has a gear reducer ratio of 1505:1. This gear reducer ratio means that for every 1,505 revolutions on the input side,...

Create a logistic regression model using Radius and Concave as explanatory variables to estimate the probability that a mass is malignant. a. Using Radius as the first explanatory variable, x1, and...

How is the market for a stock created? How do brokerage firms expedite this process? Compare the two types of brokerage services.

answer this When pus accumulates in the area between the lung and the inner surface of the chest wall (Pleural space) the condition is called: Select one: O a. Empyema O b. Chylothorax O c....

=+Consider Porters value chain and the holistic marketing orientation model.

Repeat Problem 3.7 using Eq. (3.29). Use (N 1 ) 60 from Problem 3.5. Problem 3.7 For the soil profile described in Problem 3.5, estimate an average peak soil friction angle. Use Eq. (3.31b). Problem...

Refer to Problem 3.5. Using Eq. (3.22), determine the average relative density of the sand. Problem 3.5 Following is the variation of the field standard penetration number (N 60 ) in a sand deposit:...

Refer to Problem 3.5. Using Eq. (3.28), determine the average relative density of the sand. Assume it is a fine sand. Use Eq. (3.13) to obtain (N 1 ) 60 . Problem 3.5 Following is the variation of...

Fujita, Incorporated, has no debt outstanding and a total market value of $251,600. Earnings before interest and taxes, EBIT, are projected to be $41,000 if economic conditions are normal. If there...

View Policies Current Attempt in Progress Consider the test of Ho: 62 = 14 against /1 : 62 # 14. What are the critical values for the test statistic Xo? for the significance level a = 0.01 and sample...

The president of Worldwide Gadgets would like to offer special, deeply discounted sale prices to Worldwide's most loyal and best customers under the following terms: 1. The prices will apply only to...