Question: A steel rod (E=200GPa) with a circular cross section is 7.5mlong. Determine the minimum diameter required if the rod musttransmit a tensile force of 50kN

A steel rod (E=200GPa) with a circular cross section is 7.5mlong. Determine the minimum diameter required if the rod musttransmit a tensile force of 50kN without exceeding an allowablestress of 180 MPa or stretching more than 5mm.

Step by Step Solution

★★★★★

3.37 Rating (144 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Answer E 200 G Pa P 50kn 50000 N L 75m 7500mm ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A prismatic bar with a circular cross section is loaded by tensile forces P = 65 kN (see figure). The bar has length L = 1.75 m and diameter d = 32 mm. It is made of aluminum alloy with modulus of...

A steel post AB of hollow circular cross section is fixed at the base and free at the top (see figure). The inner and outer diameters are d1 = 96 mm and d2 = 110 mm, respectively, and the length L =...

A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal (see figure). The column has outside diameter d = 250 mm and supports a load P =...

A steel [ E = 2 0 0 GPa rod with a circular cross section is 8 - m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 1 5 kN without stretching more than 4 mm...

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

In the year 2023, a devastating economic decline occurred that had a significant impact on the banking sector. This resulted in the failure of some banks, which lost a considerable amount of money...

A solid 4 3 4 0 HR Steel tie rod of length L r o d = 9 0 0 m m is employed to compress a Naval Brass bushing of length L b u s h i n g = 6 5 0 m m as shown. The tie rod has a solid circular cross...

A solid 4 3 4 0 HR Steel tie rod of length Lrod = 9 0 0 mm is employed to compress a Naval Brass bushing of length Lbushing = 6 0 0 mm as shown. The tie rod has a solid circular cross section with...

P1- The below figure shows a simplified model of bench press. a) Determine the reaction forces at A and B supports (14 points including 5 points for the free body diagram). Note: contact points of...

solve the mechanics of material problem A rod has a solid circular cross section with a diameter of 4 0 mm is subjected to the shown loads. Determine the state of stress at point A . x ? = I ? ? ( x...

The author surveyed students in one of his statistics classes about whether they smoke and whether they run red traffic lights (see Table 29). The survey was anonymous, so the students names are...

(a) What force is required to slow a 1350-kg car traveling 90.0 km/h to 25.0 km/h within 4.00 s? (b) How far does the car travel during its deceleration? (c) How long does it take for the car to come...

Alpha Manufacturing ( Pty ) Ltd is considering acquiring new specialised equipment to improve its production efficiency. The company can either purchase the equipment or lease it from a reputable...

Calculate the volume in liters of a 28.4 g/ dL nickel(1I1) chloride solution that contains 197. g of nickel(1I1) chloride (NiCI,). Be sure your answer has the correct number of significant digits. ?

The shaft shown in the figure is supported by two bearings and carries two V-belt sheaves. The tensions in the belts exert horizontal forces on the shaft, tending to bend it in the X-Z plane. Sheave...

Zigma Corporation is authorized to issue 2,000,000 shares of $6 par value capital stock. The corporation issued half the stock for cash at $9 per share, earned $486,000 during the first three months...

HOMEWORK NO. 6 Locate the centroidal xx axis and compute the moment of inertia Ix of the angle shown below. All dimensions are in millimeters. 80 29 10 40 10 X

On January 1, 2020, Fields Corporation issued ten-year bonds with a par value of $2,000,000. The bonds pay interest semiannually on June 30 and December 31 at an annual rate of 10%. The bonds were...

Let's take an objective view of the impact of listening when it comes to supplier evaluation. When you listen to the TedTalk below on The power of listening, (i). Which SPECIFIC step(s) in your...

Volume charge density is located as follows: = 0 for 2 mm, = 4 C/m 3 for 1

A copper sphere of radius 4 cm carries a uniformly distributed total charge of 5 C in free space. (a) Use Gausss law to find D external to the sphere. (b) Calculate the total energy stored in the...

Given a wave for which E s = 15e jz a x + 18e jz e j a y V/m in a medium characterized by complex intrinsic impedance, (a) Find H s ; (b) Determine the average power density in W/m 2 .

The agronomist in charge of canola seed production for a major seed-producing and marketing company is wondering if the forecast for production of seed #1234 for 2008, made by the head office, is a...

Acadian Bakers is a small sweets bakery in Houston, Texas. One of its products is a croissant. Acadian bakes the croissants from frozen croissants that it buys. For the sake of quality, the company...

Consider the usage of item # 14-46-506: 4 ft. Supersaver fluorescent lamps in Sterling Pulp Chemicals (now part of ERGO Worldwide) in the first 10 months of 2008. Month 2008 Jan10 Feb10 Mar66 Apr32...