answer fast please!h

Parti: RIP Configuration In this part, you will be given a network address that must be subostted to complete the addressing of the network shown in the Topology Diagram. A combination of RIPv2 and static routing will be required so that hosts on networks that are not directly connected will be able to communicate with cach other. PC2 Faro RIPv1 S0/0/0 S0/0/0 DCE Fa0/0 BRANCH HQ S/01 DCE 209.165.200.224/30 Default Route State Route SO/0/1 Fa0/0 1SP Internet 209.165.202.128/27 PC: PCS The addressing for the network has the following requirements: The ISP LAN will use the 209.165.202.128/27 network. The link between the ISP router and the HQ router will use the 209.165.200.224/30 network The 192.168.1.0/24 network must be subostted for use in the HQ LAN and the link between the HQ and BRANCH routers. The HQ LAN will require 50 host IP addresses. The BRANCH LAN will use the 10.10.2.0/23 network. Consider the following questions when creating your network design: How many subnets need to be created from the 192.168.1.0/24 network? What is the subnet mask for this network in dotted decimal format and in slash format? What are the network addresses of the subnets? Subnet 0 Subnet 1: TTT 209.165.202.128/27 The addressing for the network has the following requirements: - The ISP LAN will use the 209.165.202.128/27 network. The link between the ISP router and the HQ router will use the 209.165.200.220/30 network The 192.168.1.0/24 network must be suboetted for use in the HQ LAN and the link between the HQ and BRANCH routers. The HQ LAN will require 50 host IP addresses. The BRANCH LAN will use the 10.10.2.0/23 network. Consider the following questions when creating your network design: How many subnets need to be created from the 192.168.1.0/24 network? What is the subnet mask for this network in dotted decimal format and in slash format? What are the network addresses of the subnets? Subnet 0: Subnet 1: Subnet 2: Subnet 3: How many usable host IP addresses are there per subnet? How many usable hosts IP addresses are available in the BRANCH LAN? 10. Assign the last valid host address in the HQ/BRANCH WAN link to the Serial 0/0/0 interface of the BRANCH router. 11. Assign the first valid host address in the 10.10.2.0/23 network to the LAN interface on the BRANCH router. 12. Assign the last valid host address in the 10.10.2.0/23 network to PCI. Fill the following addressing table according to the conditions above, Device Interface IP Address Subnet Mask Default gateway BRANCH Fa0/0 N/A S0/0/0 N/A HQ Fa0/0 N/A S0/0/0 N/A SO/0/1 N/A ISP Fa0/0 N/A SO/0/1 N/A PCI NIC PC2 NIC PC3 NIC After cabling the network in the topology diagram and completing the basic configuration do the following: 1. Test connectivity between the devices on the network. First test the connections between directly connected devices, and then test connectivity between devices that are not directly connected, 2. RIP Routing must be configured on the BRANCH Router 3. RIP and default Route must be configured on the HQ Router 4. Static Routing must be configured on the ISP Router. 5. View the routing table after each static or dynamic route is added to observe how the routing table has changed 6. Show your work to the lab supervisor Are there any router interfaces that do not need to have RIP updates sent out? What command is used to disable RIP updates on this interfince? The HQ router needs to send the default route information to the BRANCH router in the RIP updates. What command is used to configure this