Answered step by step

Verified Expert Solution

Link Copied!

Question

1 Approved Answer

Posted on Jul 24, 2020

A single-phase 800 V/100V, 50 Hz transformer has load resistance 40 ohms find the primary current?

Step by Step Solution

★★★★★

3.60 Rating (161 Votes )

There are 3 Steps involved in it

Step: 1

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

Step: 3

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Fundamentals Of Electric Circuits

Authors: Matthew Sadiku, Charles Alexander

3rd Edition

978-0073301150, 0073301159

More Books

Students also viewed these Electrical Engineering questions

Question

★★★★★

A 25,000/240-V rms distribution transformer has a primary current rating of 75 A. (a) Find the transformer kVA rating. (b) Calculate the secondary current.

Answered: 1 week ago

Question

★★★★★

A balanced delta-connected load has a phase current IAC = 10 30 A. (a) Determine the three line currents assuming that the circuit operates in the positive phase sequence. (b) Calculate the load...

Answered: 1 week ago

Question

★★★★★

A transformer has 330 primary turns and 1340 secondary turns. The input voltage is 120 V and the output current is 15.0 A. What are the output voltage and input current?

Answered: 1 week ago

Question

★★★★★

Find the volumes of the solids generated by revolving the regions bounded by the lines and curves about the x-axis. The region between the curve and the x-axis from x = 1/4 to x = 4 y = 1/(2x)

Answered: 1 week ago

Question

★★★★★

(a) A piece of balsa wood with density 0.50 g / cm3 is released under water. What is its initial acceleration? (b) Repeat for a piece of maple with density 0.750 g / cm3. (c) Repeat for a ping-pong...

Answered: 1 week ago

Question

★★★★★

Check with your organization to see if any programs employ use cases and scenarios for deriving system capabilities and requirements. (a) Were these required by contract or a program decision? (b)...

Answered: 1 week ago

Question

★★★★★

=+c) How many factors are involved?

Answered: 1 week ago

Question

★★★★★

Surface defects have been counted on 25 rectangular steel plates, and the data are shown in Table 6E.9. Set up a control chart for nonconformities using these data. Does the process producing the...

Answered: 1 week ago

Question

★★★★★

Exercise 4-2 Closing entries LO1, 2 Following is the adjusted trial balance, with accounts in alphabetical order, for TRN Magazine as at January 31,2023 . Required: Prepore the closing entries

Answered: 1 week ago

Question

★★★★★

The demand for subassembly S is 100 units in week 7. Each unit of S requires 1 unit of T and 2 units of U. Each unit of T requires 1 unit of V, 2 units of W, and 1 unit of X. Finally each unit of U...

Answered: 1 week ago

Question

★★★★★

Which TWO of the following are FALSE with respect to Static, Environmental, and Linkage Attributes? All three should be considered "Dynamic" in nature. Some factors can be properly considered in more...

Answered: 1 week ago

Question

★★★★★

Imagine that you are implementing predictive analytics in the tourism industry. You use various techniques such as statistical modeling, data mining, and machine learning for predictions. Select the...

Answered: 1 week ago

Question

★★★★★

Find all Pythagorean triples (x, y, z) such that x = 29, y = 29, or z = 29.

Answered: 1 week ago

Question

★★★★★

Fostering a sense of shared responsibility for workplace safety promotes ethical employee concern and adherence to safety protocols. This leads to ________. A staff who are highly aware of their...

Answered: 1 week ago

Question

★★★★★

Fortes Inc. has provided the following data concerning one of the products in its standard cost system. Variable manufacturing overhead is applied to products on the basis of direct labor-hours....

Answered: 1 week ago

Question

★★★★★

forwarder to help with the transportation aspect of its supply chain. Based on the information in this chapter and your previous work for GoGreen, complete the following activities: Make a list of...

Answered: 1 week ago

Question

★★★★★

Check my work mode: This shows what is correct or incorrect for the work you have completed so far. It does not indicate com a. Barga Company purchases $39,000 of equipment on January 1, 2017. The...

Answered: 1 week ago

Question

★★★★★

Assume Eq. 6-14 gives the drag force on a pilot plus ejection seat just after they are ejected from a plane traveling horizontally at 1300 km/h. Assume also that the mass of the seat is equal to the...

Answered: 1 week ago

Question

★★★★★

Find the Norton equivalent at terminals a-b of the circuit in Fig. 4.113. 10 4 A 10 20 O b

Answered: 1 week ago

Question

★★★★★

Consider the power system shown in Fig. 11.90. Calculate: (a) The total complex power (b) The power factor 240 V ms, 50 Hz 80-150 120t/70 600

Answered: 1 week ago

Question

★★★★★

The magnitude plot in Fig. 14.76 represents the transfer function of a preamplifier. Find H(s). Figure 14.76 H (dB) A 40 20 dB/decade 2,122 0 20 dB/decade 50 500

Answered: 1 week ago

Question

★★★★★

A discount furniture store bought a waterbed at the wholesale price of $665. The regular price of the waterbed is set so that, in a 20% off sale, the rate of markup on selling price is 30%. a. What...

Answered: 1 week ago

Question

★★★★★

Fashion Master purchased mens sweaters for $72 less 40% and 15%. The normal rate of markup on selling price is 40%, and overhead is 25% of the regular selling price. The sweaters were reduced to...

Answered: 1 week ago

Question

★★★★★

Calculate the missing values

Answered: 1 week ago

Previous Question Next Question