by using Packet Tracer

Packet Tracer - Basic Switch and End Device Configuration Addressing Table Device Interface IP Address Subnet Mask Class A VLAN 1 128.107.20.10 255.255.255.0 Class-B VLAN 1 128.107.20.15 255.255.255.0 Student-1 NIC 128.107.20.25 255.255.255.0 Student-2 NIC 128.107.20.30 255.255.255.0 Objectives Configure hostnames and IP addresses on two Cisco Internetwork Operating System (IOS) switches using the command-line interface (CLI). Use Cisco IOS commands to specify or limit access to the device configurations. Use IOS commands to save the running configuration Configure two host devices with IP addresses. Verify connectivity between the two PC end devices. Scenario As a recently hired LAN technician, your network manager has asked you to demonstrate your ability to configure a small LAN. Your tasks include configuring initial settings on two switches using the Cisco los and configuring IP address parameters on host devices to provide end-to-end connectivity. You are to use two switches and two hosts/PCs on a cabled and powered network. apod: 00:00:50 Scenario As a recently hired LAN technician, your network manager has asked you to demonstrate your ability to configure a small LAN. Your tasks include configuring initial settings on two switches using the Cisco IOS and configuring IP address parameters on host devices to provide end-to end connectivity. You are to use two switches and two hosts/PCs on a cabled and powered network. Instructions Configure the devices to fulfill the requirements below. Requirements Use a console connection to access each switch. Name Class-A and Class-B switches. Use the R4Xe3 password for all lines. Use the C4aJa secret password. Encrypt all clear text passwords. Configure an appropriate message-of-the-day (MOTD) banner. Configure addressing for all devices according to the Addressing Table. Save your configurations. Verify connectivity between all devices. Note: Click Check Results to see your progress. Click Reset Activity to generate a new set of requirements. If you click on this before you complete the activity, all configurations will be lost. ID: 0000 Packet Tracer - Basic Switch and End Device Configuration Addressing Table Device Interface IP Address Subnet Mask Class A VLAN 1 128.107.20.10 255.255.255.0 Class-B VLAN 1 128.107.20.15 255.255.255.0 Student-1 NIC 128.107.20.25 255.255.255.0 Student-2 NIC 128.107.20.30 255.255.255.0 Objectives Configure hostnames and IP addresses on two Cisco Internetwork Operating System (IOS) switches using the command-line interface (CLI). Use Cisco IOS commands to specify or limit access to the device configurations. Use IOS commands to save the running configuration Configure two host devices with IP addresses. Verify connectivity between the two PC end devices. Scenario As a recently hired LAN technician, your network manager has asked you to demonstrate your ability to configure a small LAN. Your tasks include configuring initial settings on two switches using the Cisco los and configuring IP address parameters on host devices to provide end-to-end connectivity. You are to use two switches and two hosts/PCs on a cabled and powered network. apod: 00:00:50 Scenario As a recently hired LAN technician, your network manager has asked you to demonstrate your ability to configure a small LAN. Your tasks include configuring initial settings on two switches using the Cisco IOS and configuring IP address parameters on host devices to provide end-to end connectivity. You are to use two switches and two hosts/PCs on a cabled and powered network. Instructions Configure the devices to fulfill the requirements below. Requirements Use a console connection to access each switch. Name Class-A and Class-B switches. Use the R4Xe3 password for all lines. Use the C4aJa secret password. Encrypt all clear text passwords. Configure an appropriate message-of-the-day (MOTD) banner. Configure addressing for all devices according to the Addressing Table. Save your configurations. Verify connectivity between all devices. Note: Click Check Results to see your progress. Click Reset Activity to generate a new set of requirements. If you click on this before you complete the activity, all configurations will be lost. ID: 0000