Answered step by step
Verified Expert Solution
Question
1 Approved Answer
Construct the following network topology in GNS 3 or Packet Tracer simulator. Ensure that all the hostnames and network addresses are well labelled. Fig. 1
Construct the following network topology in GNS or Packet Tracer simulator. Ensure that all the hostnames and network addresses are well labelled. Fig. Network design Part Configure the router using the assigned hostnames and IP address. Part Setup Virtual PC VPC in each of the four subnets as shown above. The virtual PCs provide lightweight PC environment to execute tools such as ping, and trace route. For each faculty create two VPCs for students and two VPCs for staff. Each VPC should be able to ping the other VPC in the same subnet. Part Configure the access control list ACL on Router such that any traffic from Students subnets are blocked from entering the staff subnet. Traffic to and from other subnets should pass through. Pinging staff VPCs in both faculties from students VPCs should fail. In other words, student in each faculty should not be able to ping any staff computer in any faculty. Students can only ping students VPCs in any faculty. Staff members can ping any VPC staff and students in any faculty Part Configure DHCP services on Router such that all VPCs can get IP addresses dynamically assigned. Part Use the following checklist to ensure you network is configured correctly. Test IT student VPC cannot ping IT staff VPC IT student VPC cannot ping Arts staff VPC IT student VPC can ping Arts VPC Arts student VPC can ping IT student VPC IT staff VPC can ping Arts staff VPC Arts staff VPC can ping IT staff VPC IT staff VPC can ping IT student VPC IT staff VPC can ping Arts student VPC Arts staff VPC can ping IT student VPC Arts staff VPC can ping Arts student VPC For each of your routers make sure to save your running configuration using the command write mem For the VPCs use the save filename command to save the configurations to a file. Finally save the GNSor Packet Tracer project, ie the topology together with the startup configs. Zip the GNSor Packet Tracer project folder and submit it on Moodle with your report. Make sure your submission is complete and has all the necessary files to run the simulation.
Construct the following network topology in GNS or Packet Tracer simulator. Ensure that all the
hostnames and network addresses are well labelled.
Fig. Network design
Part
Configure the router using the assigned hostnames and IP address.
Part
Setup Virtual PC VPC in each of the four subnets as shown above. The virtual PCs provide
lightweight PC environment to execute tools such as ping, and trace route. For each faculty create
two VPCs for students and two VPCs for staff. Each VPC should be able to ping the other VPC in the
same subnet.
Part
Configure the access control list ACL on Router such that any traffic from Students subnets are
blocked from entering the staff subnet. Traffic to and from other subnets should pass through. Pinging
staff VPCs in both faculties from students VPCs should fail. In other words, student in each faculty
should not be able to ping any staff computer in any faculty. Students can only ping students VPCs in
any faculty. Staff members can ping any VPC staff and students in any faculty
Part
Configure DHCP services on Router such that all VPCs can get IP addresses
dynamically assigned.
Part
Use the following checklist to ensure you network is configured correctly.
Test
IT student VPC cannot ping IT staff VPC
IT student VPC cannot ping Arts staff VPC
IT student VPC can ping Arts VPC
Arts student VPC can ping IT student VPC
IT staff VPC can ping Arts staff VPC
Arts staff VPC can ping IT staff VPC
IT staff VPC can ping IT student VPC
IT staff VPC can ping Arts student VPC
Arts staff VPC can ping IT student VPC
Arts staff VPC can ping Arts student VPC
For each of your routers make sure to save your running configuration using the command write mem
For the VPCs use the save filename command to save the configurations to a file.
Finally save the GNSor Packet Tracer project, ie the topology together with the startup configs.
Zip the GNSor Packet Tracer project folder and submit it on Moodle with your report. Make sure
your submission is complete and has all the necessary files to run the simulation.
Step by Step Solution
There are 3 Steps involved in it
Step: 1
Get Instant Access with AI-Powered Solutions
See step-by-step solutions with expert insights and AI powered tools for academic success
Step: 2
Step: 3
Ace Your Homework with AI
Get the answers you need in no time with our AI-driven, step-by-step assistance
Get Started