Goal:Add push button controls to your Circuit Project 2.

Required:

Circuit project 2	1
Push buttons	1-3
Resistors	1-3
Jump wires	many

Cook Manual

Note: If you implemented the extra LED requirement in project 2, please remove that part before you start as it is not used in this project.

Receive push button signal and debounce

When you test with the following tutorial, find some empty space on the board. Do not remove your project 2 design from the board as we are building on it.

This example demonstrates the use of a push button as a switch: each time you press the button, the LED (or any device associated with the button) is turned on; when the button is released the LED is turned off. It also debouncesthe input, which means checking twice in a short period of time to make sure it's definitely pressed. Without debouncing, pressing the button once can appear to the code as multiple presses. You can make use of the millis()function to keep track of the time when the button is pressed.

Schematic

The code below is based on Limor Fried's version of debounce, but the logic is inverted from her example. In her example, the switch returns LOW when closed, and HIGH when open. Here, the switch returns HIGH when pressed and LOW when not pressed.

/*?Debounce

?Each time the input pin goes from LOW to HIGH (e.g. because of a push-button?press), the output pin is toggled from LOW to HIGH or HIGH to LOW. ?There's?a minimum delay between toggles to debounce the circuit (i.e. to ignore?noise).??The circuit:?* LED attached from pin 13 to ground?* pushbutton attached from pin 2 to +5V?* 10K resistor attached from pin 2 to ground??* Note: On most Arduino boards, there is already an LED on the board?connected to pin 13, so you don't need any extra components for this example.??created 21 November 2006?by David A. Mellis?modified 30 Aug 2011?by Limor Fried??This example code is in the public domain.??http://www.arduino.cc/en/Tutorial/Debounce?*/??// constants won't change. They're used here to ?// set pin numbers:?const int buttonPin = 2; // the number of the pushbutton pin?const int ledPin = 13; // the number of the LED pin??// Variables will change:?int ledState = HIGH; // the current state of the output pin?int buttonState; // the current reading from the input pin?int lastButtonState = LOW; // the previous reading from the input pin??// the following variables are long's because the time, measured in milliseconds,?// will quickly become a bigger number than can be stored in an int.?long lastDebounceTime = 0; // the last time the output pin was toggled?long debounceDelay = 50; // the debounce time; increase if the output flickers??void setup() {?pinMode(buttonPin, INPUT);?pinMode(ledPin, OUTPUT);?}??void loop() {?// read the state of the switch into a local variable:?int reading = digitalRead(buttonPin);??// check to see if you just pressed the button ?// (i.e. the input went from LOW to HIGH), and you've waited ?// long enough since the last press to ignore any noise: ??// If the switch changed, due to noise or pressing:?if (reading != lastButtonState) {?// reset the debouncing timer?lastDebounceTime = millis();?} ??if ((millis() - lastDebounceTime) > debounceDelay) {?// whatever the reading is at, it's been there for longer?// than the debounce delay, so take it as the actual current state:?buttonState = reading;?}??// set the LED using the state of the button:?digitalWrite(ledPin, buttonState);??// save the reading. Next time through the loop,?// it'll be the lastButtonState:?lastButtonState = reading;?}

Circuit Project Requirements

This circuit project will count for 4 points toward your final grade.

You need to use one push button to switch the output format of the 7-segment display. Pressing the button each time will switch the output value from "temperature(F)" to "temperature(C)" to "humidity" and back to "temperature(F)".

Switching from "temperature(F)" to "temperature(C)".

Switching from "temperature(C)" to "humidity".

Switching from "humidity" to "temperature(F)".

No flickering of 7-segment displays.

Value ARDUIN 50 AB C DE F GH Value ARDUIN 50 AB C DE F GH