Answered step by step
Verified Expert Solution
Question
1 Approved Answer
help ( b ) Figure 4 shows the schematic drawing of the plastic injection molding machine. The system consisted of TWO ( 2 ) major
helpb Figure shows the schematic drawing of the plastic injection molding machine. The system consisted of TWO major subsystems which are injection unit and clamping unit. Table shows the number of component assemblies for the injection unit and clamping unit respectively. The injection molding cycle time was an average of seconds. Note : injection molding cycle time is the total time required to complete all the stages of the injection molding cycle. Rajah memunjukkan lukisan skematik bagi mesin pengacuan suntikan plastik. Sistem ini terdiri dari DUA subsistem utama iaitu unit suntikan dan unit pengapit. Jadual menunjukkan bilangan pemasangan komponen bagi unit suntikan dan unit pengapit masingmasing. Jika kitaran masa pengacuan suntikan secara purata adalah saat. Nota : kitaran masa pengacuan suntikan ialah jumlah masa yang diperlukan untuk menyelesaikan semua peringkat kitaran pengacuan suntikan. i Determine the group reliability of the injection unit. Tentukan kebolehpercayaan kumpulan bagi unit suntikan. Marks Markah ii How many failures happen for the injection unit at every cycles. Berapa banyak kegagalan berlaku untuk unit suntikan pada setiap kitaran. Marks Markah iii Estimate the time to failure operation hours for the injection unit. Anggarkan masa untuk gagal jam operasi untuk unit suntikan. Marks Markah iv Determine the group reliability of the clamping unit. Tentukan kebolehpercayaan kumpulan bagi unit pengapit. Marks Markah v How many failures happen for the clamping unit at every cycles. Berapa banyak kegagalan berlaku untuk unit pengapit pada setiap kitaran. Marks Markah vi Estimate the time to failure operation hours for the clamping unit. Anggarkan masa untuk gagal jam operasi untuk unit suntikan. Marks Markah
helpb Figure shows the schematic drawing of the plastic injection molding machine. The
system consisted of TWO major subsystems which are injection unit and clamping
unit. Table shows the number of component assemblies for the injection unit and
clamping unit respectively. The injection molding cycle time was an average of
seconds.
Note : injection molding cycle time is the total time required to complete all the stages
of the injection molding cycle.
Rajah memunjukkan lukisan skematik bagi mesin pengacuan suntikan plastik. Sistem ini terdiri dari
DUA subsistem utama iaitu unit suntikan dan unit pengapit. Jadual menunjukkan bilangan
pemasangan komponen bagi unit suntikan dan unit pengapit masingmasing. Jika kitaran masa
pengacuan suntikan secara purata adalah saat.
Nota : kitaran masa pengacuan suntikan ialah jumlah masa yang diperlukan untuk menyelesaikan semua
peringkat kitaran pengacuan suntikan.
i Determine the group reliability of the injection unit.
Tentukan kebolehpercayaan kumpulan bagi unit suntikan.
Marks Markah
ii How many failures happen for the injection unit at every cycles.
Berapa banyak kegagalan berlaku untuk unit suntikan pada setiap kitaran.
Marks Markah
iii Estimate the time to failure operation hours for the injection unit.
Anggarkan masa untuk gagal jam operasi untuk unit suntikan.
Marks Markah
iv Determine the group reliability of the clamping unit.
Tentukan kebolehpercayaan kumpulan bagi unit pengapit.
Marks Markah
v How many failures happen for the clamping unit at every cycles.
Berapa banyak kegagalan berlaku untuk unit pengapit pada setiap kitaran.
Marks Markah
vi Estimate the time to failure operation hours for the clamping unit.
Anggarkan masa untuk gagal jam operasi untuk unit suntikan.
Marks Markah
Step by Step Solution
There are 3 Steps involved in it
Step: 1
Get Instant Access with AI-Powered Solutions
See step-by-step solutions with expert insights and AI powered tools for academic success
Step: 2
Step: 3
Ace Your Homework with AI
Get the answers you need in no time with our AI-driven, step-by-step assistance
Get Started