I need complete MS project file:

For this short tutorial, you will need to open MS Project. If you wish to duplicate these steps at home, you will need to install MS Project on your computer in order to access this application). When you first get into MS Project, you will need to select yiew from the tool bar and make sure that antt Chart is selected. Once you are in the correct view, you can begin entering tasks. The items below are a basic example of fixing several problems on an old Mustang and how they may look in the Gantt Chart. (NOTE: While not realistic, we will assume that each task takes a minimum of one day.) Remove Wheels and Tires from Mustang Remove Tires from Wheels 1 day Sandblast wheels to remove paint, chrome and rust 2 days Deliver wheels to Chrome Industry for reapplication of 2 days chrome Picku . wheels from Chrome Industr Install Tires on newly Chromed wheels Reinstall Wheels on Mustang To enter task 1., Click on the Task Name and type "Remove Wheels and Tires from Mustang" I. Enter 1 day for the Work ii. The Start and Finish day will be the same. On the next line, enter task b., \"Remove Tires from Wheels\". I. Make the Work 1 day. II. Enter the Start date as the day following the first task. Enter the remainder of the tasks with the appropriate durations and predecessors 3. NOTE: you can set the task mode to \"Automatically Schedule\" in the \"Task Mode\" column to automatically fill in the dates b. NOTEzthat you have two paths, d and teen be done concurrently Note that the Gantt chart has been created while you were adding the tasks, duration, dates and predecessors Tutorial for Adding Resources, Assigning Resources, and Viewing Proiect Costs 1. 8. 9. Next, we are going to add resources and approximate costs to our Mustang Wheel Project. The Gantt chart showing the tasks should have looked similar to this. To add resources, first go to the Resource sheet by selecting the View ribbon and clicking on Resource Sheet. Enter and Chrome Industry as resources Match the following figure to fully explain both of these resources (Resource Name, Type, Initials, Std. Rate, Ovt. Rate, Cost/Use) To add additional information for you as a resource, double click on your name. The Resource Information popup will appear You can enter your email address and other information on the General tab. Switch to the Costs Tab and note your Standard Rate and Overtime Rate was automatically entered from the Resource Sheet. Switch back to the Gantt Chart view and adjust the columns to see the Resource Names. Place your name on all tasks as the resource. 10. On the fourth task, you deliver the wheels and Chrome Industry reapplies the chrome to the wheels. Split this task to where you \"Deliver Wheels to Chrome Industry\" and Chrome Industry \"Apply Chrome to Wheels\". To do this, select the task. On the Task ribbon, select Task in the Insert section. Modify the Task names accordingly. We need to add the % Completion for each task At this point, we are assuming that tasks (1, 2, 3 and 7) have been completed. Task 4 is only 50% complete Double Click on task 1 to get the Task information window (pop-up) to open There are six tabs In the popwup In the General tab, change the Eercent complete: to 100% Complete the information on Percent Completion for each task above -: Feb;, 21 - . Feb 24 71 - : feb 21 21 YAMSSHOWTESSATWE . FS SRI\\ Remove Wheels and Tires frommystang 1 day? Wed 2/10/21 We3 2/10/21 100 ce Joe Remove Tires 1day? 1 2/11/21 The 2/11/21 Sandelast wheels to remove paint, chrome 1day 1 day? FO 2/42/21 Fri 2/12/21 -100 and rust Deliver wheels to Chrome Lust -1 caf Wed 2/10/21 Wed 2/10/21 Chrome industry for reapplicalin of Chrome 15 0575 Q5days? Tho 2/11/21 Why 2/11/21 Chrome Industry I Chrome Industry Pickup wheels from Chrome Industry 1day Mon 2/15/21 Mon 2/15/21 Ace purchase rew tires 1 day! Tue 2/16/21 Tue 2/16/21 100% Install tires on newly chromes wheels is day 1 day Web 2/17/21 Wed 2/17/ 21 Re-Install wheels on Mustang 1day 1 day? They 2/18/21 Theu 2/18/21 1. Finally, we want to look at the total cost of the project. 2. Select the Project ribbon. 3. Click Project Information in the Properties section. 4. Click on Statistics for the pop-up. 5. .The Project costs should look similar to the figure below. Project Statistics for 'Projectl' X Start Finish Current Wed 2/10/21 Thu 2/18/21 Baseline NA NA Actua Wed 2/10/21 NA Variance 0d od Duration Work Cost Current 7d? 8.5d $6,800.00 Baseline od 0d $0.00 Actual 4.12d 5d $1,600.00 Remaining 2.88d? 3.5d $5,200.00 Percent complete: Duration: 59% Work: 59% CloseLook at the Project Information Statistics again and note the differences. Project Statistics for 'Projectl' X Start Finish Current Wed 2/10/21 Fri 2/19/21 Baseline Wed 2/10/21 Fri 2/19/21 Actual Wed 2/10/21 Fri 2/19/21 Variance od Duration Work Cost Current 8d? 9d $11,200.00 Baseline 8d 8.5d $7,200.00 Actual 8d 9d $11,200.00 Remaining od? od $0.00 Percent complete: Duration: 100% Work: 100% Close