Kitchen Supply, Inc. (KSI), manufactures three types of flatware: institutional, standard, and silver. It applies all indirect costs according to a predetermined rate based on direct labor-hours. A consultant recently suggested that the company switch to an activity-based costing system and prepared the following cost estimates for year 2 for the recommended cost drivers. Recommended Cost Driver Number of orders Number of production runs Pounds of materials used Estimated Cost $ 46,000 198,000 260,000 Estimated Cost Driver Activity 200 orders 110 runs 130,000 pounds Activity Processing orders Setting up production Handling materials Machine depreciation and maintenance Performing quality control Packing Total estimated cost Machine-hours Number of inspections Number of units 247,800 51,200 138,000 $940,200 13,000 hours 40 inspections 460,000 units 5 In addition, management estimated 7,100 direct labor-hours for year 2. Assume that the following cost driver volumes occurred in January, year 2. Number of units produced Direct materials costs Direct labor-hours Number of orders Number of production runs Pounds of material Machine-hours Number of inspections Units shipped Institutional 58,000 $37,000 440 13 3 16,000 570 4 58,000 Standard 22,000 $24,000 440 9 3 5,000 140 3 22,000 Silver 9,000 $17,000 610 5 6 3,100 60 3 9,000 Actual labor costs were $15 per hour. Required: Required: a. (1) Compute a predetermined overhead rate for year 2 for each cost driver using the estimated costs and estimated cost driver units prepared by the consultant. (2) Compute a predetermined rate for year 2 using direct labor-hours as the allocation base, b. Compute the production costs for each product for January using direct labor-hours as the allocation base and the predetermined rate computed in requirement a(2) c. Compute the production costs for each product for January using the cost drivers recommended by the consultant and the predetermined rates computed in requirement a. (Note: Do not assume that total overhead applied to products in January will be the same for activity-based costing as it was for the labor-hour-based allocation.) Complete this question by entering your answers in the tabs below. Reg A1 Reg A2 Reg B Reqc Compute a predetermined overhead rate for year 2 for each cost driver using the estimated costs and estimated cost driver units prepared by the consultant. (Round your answers to 2 decimal places.) Rate per order Activity Processing orders Setting up production Handling materials ring machines Performing quality control Packing per run per pound per machine hour per inspection per unit Actual labor costs were $15 per hour. Required: a. (1) Compute a predetermined overhead rate for year 2 for each cost driver using the estimated costs and estimated cost driver units prepared by the consultant. (2) Compute a predetermined rate for year 2 using direct labor-hours as the allocation base. b. Compute the production costs for each product for January using direct labor-hours as the allocation base and the predetermined rate computed in requirement a(2), c. Compute the production costs for each product for January using the cost drivers recommended by the consultant and the predetermined rates computed in requirement a. (Note: Do not assume that total overhead applied to products in January will be the same for activity-based costing as it was for the labor-hour-based allocation.) Complete this question by entering your answers in the tabs below. Reg A1 Reg A2 Reg B Regc Compute a predetermined rate for year 2 using direct labor-hours as the allocation base. (Round your answer to 2 decimal places.) Predetermined rate per direct labor-hour Actual labor costs were $15 per hour. Required: a. (1) Compute a predetermined overhead rate for year 2 for each cost driver using the estimated costs and estimated cost driver units prepared by the consultant (2) Compute a predetermined rate for year 2 using direct labor-hours as the allocation base. b. Compute the production costs for each product for January using direct labor-hours as the allocation base and the predetermined rate computed in requirement a(2). c. Compute the production costs for each product for January using the cost drivers recommended by the consultant and the predetermined rates computed in requirement a. (Note: Do not assume that total overhead applied to products in January will be the same for activity based costing as it was for the labor-hour-based allocation.) Complete this question by entering your answers in the tabs below. Reg A1 Reg A2 Reg B Reqc Compute the production costs for each product for January using direct labor-hours as the allocation base and the predetermined rate computed in requirement a(2). (Do not round intermediate calculations.) Account Institutional Standard Silver Total Direct materials $ 37,000 $ 24,000 $ 17,000 $ 78,000 Direct labor Indirect costs Total cost c. Compute the production costs for each product for January using the cost drivers recommended by the consultant and the predetermined rates computed in requirement a. (Note: Do not assume that total overhead applied to products in January will be the same for activity-based costing as it was for the labor-hour-based allocation.) Complete this question by entering your answers in the tabs below. Req A1 Req A2 Reg B Reqc Compute the production costs for each product for January using the cost drivers recommended by the consultant and the predetermined rates computed in requirement a. (Note: Do not assume that total overhead applied to products in January will be the same for activity-based costing as it was for the labor-hour-based allocation.) (Do not round intermediate calculations.) Show less Silver Total Institutional Standard $ 37,000 $ 24,000 $ 17,000 $ 78,000 Account Direct materials Direct labor Indirect costs Processing orders Setting up production Handling materials Using machines Performing quality control Packing Total cost
