Answered step by step
Verified Expert Solution
Question
1 Approved Answer
MEIE 4 1 0 2 : MACHINE DESIGN I M FINAL EXAM: DECEMBER 3 0 , 2 0 2 3 ( FL - 2 0
MEIE : MACHINE DESIGN I M FINAL EXAM: DECEMBER FL FI PART : ANSWER THE FOLLOWING QUESTIONS MARKS Mark A gear of pitch circle diameter has teeth. The circular pitch will nearly I a tooth b tooth c tooth d tooth Mark All of the following the common failure criteria used for shaft design except a DEGoodman TOTAL MARKS: MARKS, TIME: HRS PART : ANSWER THE FOLLOWING QUESTIONS MARKS c DEASME Elliptic bGerber Mark The path of contact in d DECoulomb a Along an involute c Along the base circle b Along a straight line Mark Which material property stresses? a Brittleness b Hardness c Ductility d Toughness Mark In shaft design for stress, the distortion energy theory is used to assess: a Thermal resistance b Static strength c Fatigue strength d Impact resistance Mark When designing a shaft for stress, which factor is not typically considered? a Fatigue strength b Corrosion resistance c Creep resistance d Static strength Mark True or False: Tighter bearing tolerances are always preferred for achieving higb performance. a True b False Mark Excessive bearing noise can indicate which of the following issues? a Wear and damage b Misalignment c Poor Iubrication d All of the choices Mark True or False: The primary cause of failure in a properly maintained and lubricated rollingcontact bearing is misalignment. a True b False Mark In a variable pitch spring, the pitch of the coils: a Varies along the length b Is inversely proportional to the load c Remains constant d Is directly proportional to the load Mark In a torsion spring, the energy is stored primarily through: a Tension b Twisting c Compression d Bending Mark Leaf springs are best suited for applications requiring a High frequency vibration isolation b Small space utilization c Precision control d Low frequency vibration isolation Page of
MEIE : MACHINE DESIGN I
M
FINAL EXAM: DECEMBER
FL
FI
PART : ANSWER THE FOLLOWING QUESTIONS MARKS
Mark A gear of pitch circle diameter has teeth. The circular pitch will nearly I
a tooth
b tooth
c tooth
d tooth
Mark All of the following the common failure criteria used for shaft design except
a DEGoodman
TOTAL MARKS: MARKS, TIME: HRS
PART : ANSWER THE FOLLOWING QUESTIONS MARKS
c DEASME Elliptic
bGerber
Mark The path of contact in d DECoulomb
a Along an involute
c Along the base circle
b Along a straight line
Mark Which material property stresses?
a Brittleness
b Hardness
c Ductility
d Toughness
Mark In shaft design for stress, the distortion energy theory is used to assess:
a Thermal resistance
b Static strength
c Fatigue strength
d Impact resistance
Mark When designing a shaft for stress, which factor is not typically considered?
a Fatigue strength
b Corrosion resistance
c Creep resistance
d Static strength
Mark True or False: Tighter bearing tolerances are always preferred for achieving higb performance.
a True
b False
Mark Excessive bearing noise can indicate which of the following issues?
a Wear and damage
b Misalignment
c Poor Iubrication
d All of the choices
Mark True or False: The primary cause of failure in a properly maintained and lubricated rollingcontact bearing is misalignment.
a True
b False
Mark In a variable pitch spring, the pitch of the coils:
a Varies along the length
b Is inversely proportional to the load
c Remains constant
d Is directly proportional to the load
Mark In a torsion spring, the energy is stored primarily through:
a Tension
b Twisting
c Compression
d Bending
Mark Leaf springs are best suited for applications requiring
a High frequency vibration isolation
b Small space utilization
c Precision control
d Low frequency vibration isolation
Page of
Step by Step Solution
There are 3 Steps involved in it
Step: 1
Get Instant Access with AI-Powered Solutions
See step-by-step solutions with expert insights and AI powered tools for academic success
Step: 2
Step: 3
Ace Your Homework with AI
Get the answers you need in no time with our AI-driven, step-by-step assistance
Get Started