Answered step by step
Verified Expert Solution
Question
1 Approved Answer
Place here the screenshot image(s) of your simulation used to test your results and type your explanation in RED below your images Part B Given
Place here the screenshot image(s) of your simulation used to test your results and type your explanation in RED below your images Part B Given the following circuit -00 F1 SW1 SW2 SW3 SW4 SW5 SW6 BAT1 R1 R2 RJ R4 R5 R6 12 V 24 0 48 0 8 0 1. Calculate the current through each Resistance R1 to RG when its correspondent switch is closed (e.g. the current through R1 when the switch SW1 is closed, the current through R2 when the switch SW2 is closed, etc.) Type your solution of question 1) in RED or PASTE the image of your handwriting solution HERE 2. If the value of the Fuse F1 is 1 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? - Justify your answer with your calculations. Type your solution of question 2) in RED or PASTE the image of your handwriting solution HERE 3. If the value of the Fuse F1 is 2 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? - Justify your answer with your calculations. Type your solution of question 3) in RED or PASTE the image of your handwriting solution HERE 4. If the value of the Fuse F1 is 3 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? - Justify your answer with your calculations Type your solution of question 4) in RED or PASTE the image of your handwriting solution HERE5. Calculate the minimum value of the Fuse F1 that will allow ALL the switches to be close Type your solution of question 5) in RED or PASTE the image of your handwriting solution HERE 6. Test your results using the simulation https://phet.colorado.edu/sims/html/circuit-construction- kit-do/latest/circuit-construction-kit-de_en.html L Place here the screenshot image(s) of your simulation used to test your results and type your explanation in RED below your images Part C You are the light technician of the performance. The Director ORDERED you (you do not have a choice!!!) to use the two channel Dimmer PPQQ2019. Every channel has a Maximum Current Imax=30 Amps, and the Voltage in the output of the channel depends of the Variable ALPHA (your control slide!) that changes from 0% to 100% following this NON LINEAR relation Vout(ALPHA) = 120 Volts . (ALPHA)? 10000 Also the Director requested tom place the seven lamps (Lamp 1 to Lamp 7) in the configuration presented below. Breaker max 30 Amps Lamp #1 Lamp #2 Lamp #3 Dimmer 600 Watts 1200 Watts 1800 Watts Alpha Ch1 Ch1 Figure 1 - Diagram of the lamps connected to Channel 1Breaker Imax 30 Amps Lamp #4 Lamp # 5 Lamp # 6 Lamp # 7 Dimmer 1200 Watts () 1200 Watts 1800 Watts X 1800 Watts Alpha Ch2 Ch2 Figure 2 - Diagram of the lamps connected to Channel 2 Please answer the questions below: 1) Before you start using the unfamiliar Dimmer PPQQ2020 you decided to make an experiment with the device to better understand how the dimmer work a. Define the question of your experiment b. Define the variables of your experiment Define the hypothesis of your experiment Type your solution of questions 1) a, b, and c in RED or PASTE the image of your handwriting solution HERE 2) Knowing the relation between the Control slide ALPHA (0 to 100) and the voltage across the output of each channel Vout a. Make a graph the shows the relation between the variable ALPHA and the Voltage on the output of the Channel Vout (you can use EXCEL, Google Sheet, etc.) Paste HERE the image of the requested table and graph - Copy from the spreadsheet the table and the graph and paste them here as AN IMAGE b. Which will be the voltage for: i. ALPHA= 25% ii. ALPHA= 50% iii. ALPHA = 75% iv. ALPHA = 100% Type your solution of questions 2) b. I, ii, iii and iv in RED or PASTE the image of your handwriting solution HERE All the lamps from Lamp #1 to Lamp #7 are designed to work with a nominal Voltage Vlamp of 120V and their resistance Rlamp is constant and do not depends on the temperature. Using this information solve the questions below.3) The Channel 1 has three lamp connected as shown in the Figure 1 and you want to be sure that will not be a black-out in the middle of the performance. Please determine if the Channel 1 can work using the variable ALPHA from 0% to 100%. Yes/No, justify your answer with your calculations. No justifications - No points. Type your solution of only question 3) in RED or PASTE the image of your handwriting solution HERE 4) The Channel 2 has four lamp connected as shown in the Figure 2 and again you want to be sure that will not be a black-out in the middle of the performance. Please determine if the Channel 1 can work using the variable ALPHA from 0% to 100. Yes/No, justify your answer with your calculations. No justifications - No points Type your solution of only question 4) in RED or PASTE the image of your handwriting solution HERE 5) What is the value of the resistors of all the lamps from Lamp#1 to Lamp#7? Type your solution of only question 5) in RED or PASTE the image of your handwriting solution HERE 6) What is the maximum value of the variable ALPHA that will allow the channel 2 produce its maximum light output? Type your solution of only question 6) in RED or PASTE the image of your handwriting solution HERE 7) What do you will suggest to the Director to do to be able to use the Channel 2 without the fear that the breaker will open in the middle of the performance? Type your solution of only question 7) in RED or PASTE the image of your handwriting solution HERE Review BEFORE submitting your work 1) Remove the watermark Open the concerned document. For latest Word editions, Select the Design tab (click the Page Layout tab For Word 2010 and Word 2007). Locate the Page Background tab and select Watermark. Select Remove Watermark. Your document should no longer display the watermark.Question #5 READ ALL THE QUESTION BEFORE YOU START!! 1. DOWNLOAD THE FILE TEMPLATE QUESTION#S.DOCX, ANSWER THE QUESTION - PLACING THE ANSWERS (TYPE THEM IN RED) OR PASTING AN IMAGE OF YOUR SOLUTION IN ITS RESPECTIVE PLACE BY EDITING THE FILE TEMPLATE QUESTION#S.DOCX. (EDITING MEANING TYPING YOUR SOLUTION OR PASTING IN PLACE AN IMAGE - READABLE - OF YOUR HANDWRITING SOLUTION) 2. WHEN YOU FINISHED ANSWERING THE QUESTION, SAVE THIS FILE AS A PDF FILE QUESTION#SPDF 3. SUBMIT THIS FILE QUESTION#S. PDF Part A Given the following electric circuit R1 772 0 Amperemeter The voltmeters BAT R2 R3 9V 10 0 10 0 Voltmeter shows 6 Volt It is known that the voltage measured by the voltmeter is 5 Volt 1. Calculate the value of the current loa through the battery BAT1 (It is the current that the amperemeter shows) 2. Calculate the value of the Resistance R1 3. Calculate the Power provided por the battery to the system 4. Calculate the Power released by each one of the Resistances Ri, Ra, and Ra 5. Explain if there is a relation between the Power provided por the battery Pawn and the Power released by the Resistances Ri, Ra, and Ra- Justify your answer with your calculations Type your solution of questions 1) to 5) in RED or PASTE the image of your handwriting solution HERE 6. Test your results using the simulation https://phet.colorado.edu/sims/html/circuit- construction-kit-dc/latest/circuit-construction-kit-dc_en.html P
Step by Step Solution
There are 3 Steps involved in it
Step: 1
Get Instant Access to Expert-Tailored Solutions
See step-by-step solutions with expert insights and AI powered tools for academic success
Step: 2
Step: 3
Ace Your Homework with AI
Get the answers you need in no time with our AI-driven, step-by-step assistance
Get Started