Question: Consider the hole diameter data in Exercise 6.5. Esti- mate process capability using x and R charts. If spec- ifications are at 0 0.01, calculate Cp, Cpk, and Cpkm. Interpret these ratios. (Plesase Just answer this)

Table 6E.2 Hole Diameter Data for Exercise 6.5 Sample Number X2 X3 X4 X5 -30 +50 -20 +10 +30 0 +50 -60 -20 +30 -50 +10 +20 +30 +20 -10 -10 +30 -20 +50 +20 5 0 N O OI A W N- -40 +50 +20 +10 0 0 +40 -40 +20 0 0 +20 -20 -10 +70 -30 +30 -10 0 0 0 +20 -20 +10 10 +10 +20 +30 +10 +50 11 +40 0 +20 0 +20 12 +30 +20 +30 +10 +40 13 +30 -30 0 +10 +10 14 +30 -10 +50 -10 -30 15 +10 -10 +50 +40 0 16 0 0 +30 -10 0 17 +20 +20 +30 +30 -20 18 +10 -20 +50 +30 +10 19 +50 -10 +40 +20 0 20 +50 0 +30 +10 On this scale, a reading of zero corresponds to the correct fill height. Fifteen samples of size n = 10 have been analyzed, and the fill heights are shown in Table 6E.3. Table 6E.3 Fill Height Data for Exercise 6.6 Sample Number X1 X2 X3 XA X5 X6 X7 X8 X9 X10 2.5 0.5 2.0 -1.0 1.0 -1.0 0.5 1.5 0.5 -1.5 2 0.0 0.0 0.5 1.0 1.5 1.0 -1.0 1.0 1.5 -1.0 3 1.5 1.0 1.0 -1.0 0.0 -1.5 -1.0 -1.0 1.0 -1.0 4 0.0 0.5 -2.0 0.0 -1.0 1.5 -1.5 0.0 -2.0 -1.5 5 0.0 0.0 0.0 -0.5 0.5 1.0 -0.5 -0.5 0.0 0.0 6 1.0 -0.5 0.0 0.0 0.0 0.5 -1.0 1.0 -2.0 1.0 7 1.0 -1.0 -1.0 -1.0 0.0 1.5 0.0 1.0 0.0 0.0 8 0.0 -1.5 -0.5 1.5 0.0 0.0 0.0 -1.0 0.5 -0.5 9 -2.0 -1.5 1.5 1.5 0.0 0.0 0.5 1.0 0.0 1.0 10 -0.5 3.5 0.0 -1.0 -1.5 -1.5 -1.0 -1.0 1.0 0.5 11 0.0 1.5 0.0 0.0 2.0 -1.5 0.5 -0.5 2.0 -1.0 12 0.0 -2.0 -0.5 0.0 -0.5 2.0 1.5 0.0 0.5 -1.0 13 -1.0 -0.5 -0.5 -1.0 0.0 0.5 0.5 -1.5 -1.0 -1.0 14 0.5 1.0 -1.0 -0.5 -2.0 -1.0 -1.5 0.0 1.5 1.5 15 1.0 0.0 1.5 1.5 1.0 -1.0 0.0 1.0 -2.0 -1.5