surface the normal force is just the weight of the object (mg). If an object is on an incline, F_N has to be corrected via the equation F_N= mg cos with being the angle of the incline. In this experiment, we will only measure friction on a horizontal surface, so we don't need to concern ourselves with the issues affecting friction on an incline.

The constant of proportionality is called the coefficient of friction, . The force of friction when two contacting surfaces are sliding over each other can be calculated by:

where F_fr is the force of friction; F_N is the normal force; and _k or _s are the coefficient of friction, which is a proportionality constant. The force of friction is parallel to the contact surfaces and opposite to the direction of motion. The term _k stands for coefficient of kinetic (or sliding) friction, which applies when the surfaces are moving with respect to each other.

When an object is at rest on a surface and we attempt to push it, the frictional force is opposing the pushing force. As long as the pushing force is less than the friction force, the object will not move. There is a threshold value of the pushing force beyond which a larger pushing force will cause the body to start sliding. It is this threshold value which is related tothe coefficient of static friction, _s. However, when an object is already in movement, the friction that it experiences is related to itscoefficient of kinetic friction,_k. When comparing published k and s values for identical materials, we see that s is slightly larger than k . This indicates that it takes more force to start moving a material than keeping it moving.

PROCEDURE

For purposes of data recording, we will use Newtons (N) as this is the unit of Force in the International Systems of Units. For the purposes of this experiment, we can convert any mass to force using the following formula:

Measurement setup

For each measurement setup described in this section, we will measure two forces. First, we will measure the force that we need to exert on a wooden block so it starts moving from a resting position. This force is related to thecoefficient of static friction. The second force is the force that we need to exert on the wooden block to keep it moving. This force is related to thecoefficient of dynamic friction.

Because the wooden blocks in your lab kit are too light to produce accurate results, we will augment their mass by adding an object of constant weight, for example a can of soda. The experimental setup can be seen in figure 1 below. You can use any other object that you may have around instead of the soda can.

Figure 1: Experimental Setup

We will perform two types of measurements:

• Force of Static Friction (F_s): Starting from the block at rest, pull from the spring scale until the block starts moving. Record this force.

• Force of Kinetic Friction (F_k): Starting from the block at rest, pull from the spring scale until the block starts moving and continue pulling until it moves at a constant speed. Record this force.

You should observe that F_k is lower than F_s. We will repeat these measurements using several materials as well as in different configurations for the wooden blocks.

Question 1

What is the mass of the system made of the wooden block and the soda can (or the other object that you are using)?

Question 2

Convert the mass measured in Question 1 to its weight in Newtons. This is the value of F_N that will be used in the calculations for the tables.

SURFACES

Wood / Wood (larger surface)

For this case, we will use the larger surface of the wooden block as was shown in Figure 1. Measure F_s and F_k as indicated in Section 3.1. Run 5 trials, completing Table 1 below.

Wood / Wood (smaller surface)

For this section, turn the wooden block on its side as shown in Figure 2 and repeat the experiment, completing Table 2.

Figure 2: Wooden block on its side (courtesy of Chad Saunders, TESU student)

Wood / Glass

For this section, use the glass surface of your wooden block to repeat the measurements and complete Table 3.

Other surfaces

Repeat the measurements using other surfaces (for example, Wood / Sandpaper, Wood / Carpet, Glass / Carpet, etc.) When completing Table 4 below, make sure that you indicate the surfaces you used.

ANALYSIS OF RESULTS

QUESTION 3

Study the results from Table 1 and Table 2. What can you conclude about these results?

QUESTION 4

Using the data from the same tables, do you think that the ratio of _k to _s is constant in both cases? If so, what do you think this indicates?

QUESTION 5

Studying the standard deviation data from all the 4 tables, which experiment do you think is the most reproducible? Why?

QUESTION 6

In general, how does the coefficient of static friction compare to the coefficient of dynamic friction?

QUESTION 7

In designing machinery, would we prefer to use materials with larger or smaller coefficient of friction? Explain your reasoning.

QUESTION 8

In driving a vehicle, would you prefer to use materials for the contact between the wheels and the road with larger or smaller coefficient of friction? Explain your reasoning.

LABORATORY REPORT

Please do a laboratory report using Word that contains at least these elements below:

• Introduction: what is the purpose of this laboratory experiment?
• Description of how you performed the different parts of this exercise. At the very least, this part should contain the answers to questions 1-8 above. You should also include procedures, etc. Adding pictures to your lab report showing your work as needed always increases the value of the report.
• Conclusion: What area(s) you had difficulties with in the lab; what you learned in this experiment; how it applies to your coursework and any other comments.