Answered step by step
Verified Expert Solution
Link Copied!

Question

1 Approved Answer

The standard methods that apply to analytical chemistry still applies with radiochemical analytes. When the behavior of a radionuclide has to be taken into consideration

The standard methods that apply to analytical chemistry still applies with radiochemical analytes. When the behavior of a radionuclide has to be taken into consideration such details are taken care of: The common methods available for separation are: (i) Complexation (ii) solvent (iii) Tracer adsorption.
Adsorption becomes very vital because the samples are recovered from radioactive matrix. Adsorption utilizes special equations called Langmuir adsorption isotherms which follows the equation.
x=xmbCe1+bCe, eqn 1.
Where x,=xm, the amount of solute adsorbed x per unit mass of adsorbent m.
Ce= Equilibrium constant of solute
xm= Amount of solute adsorbed per unit mass adsorbate required for mono layer of layer capacity.
b ,= a constant related to heat capacity of adsorption of material =Q[bexp(-HRT)]
When the eqn 1 is rearranged, it becomes:
Cex=1bxm+Cexm, eqn 2.
Which can further be rearranged as:
1x=1xm+1Ce(1bxm), eqn 3
Using equation 3, a linear plot of 1x against 1Ce is formed. The slope for this linear plot is 1bxm and y intercept as 1xm
The adsorption of one radioactive substance absorption behavior was evaluated and its data was as show below in table below.
\table[[sn,\table[[Mass of],[adsorbent]],\table[[Volume of],[flask mL]],\table[[Mass],[adsorbate],[adsorbed]],\table[[Final COD],[(mg/L) C]],\table[[xm
The standard methods that apply to analytical chemistry still applies with radiochemical analytes. When the behavior of a radionuclide has to be taken into consideration such details are taken care of: The common methods available for separation are: (i) Complexation (ii) solvent (iii) Tracer adsorption.
Adsorption becomes very vital because the samples are recovered from radioactive matrix. Adsorption utilizes special equations called Langmuir adsorption isotherms which follows the equation.
x=xmbCe1+bCe, eqn 1.
Where x,=xm, the amount of solute adsorbed x per unit mass of adsorbent m.
Ce,= Equilibrium constant of solute
xm= Amount of solute adsorbed per unit mass adsorbate required for mono layer of layer capacity.
b ,= a constant related to heat capacity of adsorption of material =Q[bexp(-HRT)]
When the eqn 1 is rearranged, it becomes:
Cex=1bxm+Cexm, eqn 2.
Which can further be rearranged as:
1x=1xm+1Ce(1bxm), eqn 3
Using equation 3, a linear plot of 1x against 1Ce is formed. The slope for this linear plot is 1bxm and y intercept as 1xm
The adsorption of one radioactive substance absorption behavior was evaluated and its data was as show below in table below.
\table[[sn,\table[[Mass of],[adsorbent]],\table[[Volume of],[flask mL
image text in transcribed

Step by Step Solution

There are 3 Steps involved in it

Step: 1

blur-text-image

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

blur-text-image_2

Step: 3

blur-text-image_3

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Thermodynamics for Engineers

Authors: Kenneth A. Kroos, Merle C. Potter

1st edition

1133112862, 978-113311286

More Books

Students also viewed these Chemical Engineering questions

Question

Draw a schematic diagram of I.C. engines and name the parts.

Answered: 1 week ago

Question

Does the research have to be based in an organisation?

Answered: 1 week ago

Question

Are implementable recommendations a requirement for the project?

Answered: 1 week ago