To avoid the problem of interference in a pair of spur gears using a 20 pressure angle,

Question:

To avoid the problem of interference in a pair of spur gears using a 20◦ pressure angle, specify the minimum number of teeth allowed on the pinion for each of the following gear ratios.
(a) 2 to 1
(b) 3 to 1
(c) 4 to 1
(d) 5 to 1

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Shigleys Mechanical Engineering Design

ISBN: 978-1121345317

9th edition

Authors: Richard G. Budynas, J. Keith Nisbett

See More Books

Question Posted: May 30, 2013 07:59 AM

See More Questions

In order to avoid the problem of implied volatilities being different for different strike prices and maturities, a student of the Black-Scholes theory suggests making the stock's volatility a...
One scheme to avoid the problem of p reallocation versus waste or lack of contiguity is to allocate portions of increasing size as the file grows. For example, begin with a portion size of one block,...
One might suppose that we can avoid the problem of variable conflict in unification during backward chaining by standardizing apart all of the sentences in the knowledge base once and for all. Show...
If the protein produced full length antibody, what would be the next step after centrifugation?
A transformer is used to match an amplifier with an 8- load as shown in Fig. 13.119. The Thevenin equivalent of the amplifier is: VTh = 10 V, ZTh = 128 . (a) Find the required turns ratio for...
Under what circumstances do page faults occur? Describe the actions taken by the operating system when a page fault occurs.
Describe the home-buying process.? lo1
The stockholders equity for Dairy Place Drive-Ins (DP) on December 31, 2012, follows: On April 16, 2013, the market price of DP common stock was $20 per share. Assume DP distributed an 18% stock...
Bed & Bath, a retailing company, has two departments: hardware and linens. A recent monthly income statement for the company follows: New Income Statement Department Department Hardware Linens Total...
The following are audit procedures from different transactioncycles: 1. Examine sales invoices for evidence of internal verification ofprices, quantities, and extensions. 2. Select items from the...
A parallel helical gearset consists of a 19-tooth pinion driving a 57-tooth gear. The pinion has a left-hand helix angle of 30, a normal pressure angle of 20, and a normal module of 2.5 mm. Find: (a)...
Repeat Prob. 138 with a 25 pressure angle. To avoid the problem of interference in a pair of spur gears using a 20 pressure angle, specify the minimum number of teeth allowed on the pinion for each...
A sphere and a circular cylinder (with its axis perpendicular to the flow) are mounted in the same free stream. A pressure tap exists at the top of the sphere, and this is connected via a tube to one...
Let two planes be given by 2x-y+z = 8 and z = x+y-5 (a) Find the angle between the two planes. Leave your answer in degrees and round to the nearest tenth. (b) Find the vector equation of the line of...
9-2. The profile of a gear tooth shown in Fig. P9.2 is approximated by the trigonometric equation y(x) = a. Estimate the area A using eight rectangles of equal width A x = 1/8, b. Calculate the exact...
tube is hinged to a rotating base as shown in Fig. 4. At the instant shown, the base rotates about the z axis with a constant angular velocity ! 1 = 2 rad/s. At the same instant, the 2 tube rotates...
Find the limit analytically. -7x2+5x-10 lim 0 9x+13x+11 Find the limit analytically. lim +80 4x-13 5x+6x-11
Write a recursive function for the running time T(n) of the function given below. Prove using the iterative method that T(n) = (n). function( int n) { if(n=1) return; for(int i = 1; i
How could she have used principles of motivation discussed in this chapter to ensure the implementation of Korean Airs high standards for employees?
What mass of KBr (in grams) should you use to make 350.0 mL of a 1.30 M KBr solution?
Airline fares have declined in real terms since the introduction of the Douglas DC- 3 throughout the regulated era. What has enabled this decline?
Convert the following to appropriate ips units: (a) A length of 1.5 m. (b) A stress of 600 MPa. (c) A pressure of 160 kPa. (d) A section modulus of 1.84 (105) mm3. (e) A unit weight of 38.1 N/m. ( f...
Generally, final design results are rounded to or fixed to three digits because the given data cannot justify a greater display. In addition, prefixes should be selected so as to limit number strings...
Repeat Prob. 111 for: (a) = F/A, where A = d2/4, F = 120 kN, and d = 20 mm. (b) = 32 Fa/d3, where F = 800 N, a = 800 mm, and d = 32 mm. (c) Z = (/32d)(d 4 d 4 ) for d = 36 mm and d i = 26 mm. (d)...
Problem 1 4 - 1 9 ( Algo ) Convertible bonds; induced conversion; bonds with detachable warrants [ LO 1 4 - 5 ] Bradley - Link s December 3 1 , 2 0 2 1 , balance sheet included the following items:...
Bought an old van for 4000 from Peters promising to pay laterwhat is the transactions
Company has a following trade credit policy 1/10 N45. If you can borrow from a bank at 9,5% annual rate, would it be beneficial to borrow money and pay off invoices earlier?

To avoid the problem of interference in a pair of spur gears using a 20 pressure angle,

Question:

Step by Step Answer:

a b Repeating a with m 3 N P 1498 teeth Rounding up N P 15 teeth c Repeating a with m 4 ...View the full answer

Shigleys Mechanical Engineering Design

Students also viewed these Mechanical Engineering questions