When a carpenter shuts off his circular saw, the 10.0-inchdiameter blade slows from 3984 rpm to 0

Question:

When a carpenter shuts off his circular saw, the 10.0-inchdiameter blade slows from 3984 rpm to 0 in 1.25 s.

(a) What is the angular acceleration of the blade?

(b) What is the distance traveled by a point on the rim of the blade during the deceleration?

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Physics

ISBN: 978-0321976444

5th edition

Authors: James S. Walker

See More Books

Question Posted: Aug 31, 2017 11:25 AM

See More Questions

The peripheral speed of the tooth of a 10-in.-diameter circular saw blade is 150 ft/s when the power to the saw is turned off. The speed of the tooth decreases at a constant rate, and the blade comes...
The carpenter slowly pushes the uniform board horizontally over the top of the saw horse. The board has a uniform weight density and the saw horse has a weight W and a center of gravity at G....
The carpenter slowly pushes the uniform board horizontally over the top of the saw horse. The board has a uniform weight of 3lb/ft, and the saw horse has a weight of 15 lb and a center of gravity at...
All adiabatic temperature changes occur as a result of a. changes in the absolute humidity of the air. b. expansion or compression of the air. c. changes is specific humidity d. the addition or...
Common versus Preferred Stock Suppose a company has a preferred stock issue and a common stock issue. Both have just paid a $2 dividend. Which do you think will have a higher price, a share of the...
The Allen Company is a wholesale distributor of automotive replacement parts. Initial amounts taken from Allens accounting records are as follows: Inventory at December 31, 2007 (based on physical...
Which method from question 2 is better? How do you know that? LO.1
Minelli Enterprises uses large amounts of copper in the manufacture of ceiling fans. The firm has been very concerned about the detrimental impact of rising copper prices on its earnings and has...
Required information [The following information applies to the questions displayed below.] At the beginning of Year 1, Oak Consulting had the following normal balances in its accounts: Account...
Your co-worker wanted the afternoon off and you graciously agreed to finish up his work for him. Use the completed journal entries provided and post them to their T-accounts. Assume all accounts...
The Earth's rate of rotation is constantly decreasing, causing the day to increase in duration. In the year 2006 the Earth took about 0.840 s longer to complete 365 revolutions than it did in the...
The drill used by most dentists today is powered by a small air turbine that can operate at angular speeds of 350,000 rpm. These drills, along with ultrasonic dental drills, are the fastest turbines...
Use the graph above and to the right, which shows the daily low and high temperatures, in degrees Celsius, for the week in the outback in Australia. Determine the following temperatures in degrees...
Sketch the curves with equations given in question 3 parts a, b, c and d, labelling any stationary points with their coordinates. Data from Question 3 Find the coordinates of the points where the...
Trace the polygon and point P on paper. Then draw a rotation of the polygon the given number of degrees about P. 130 Q R T P S
Name any devices other than the three mentioned in Section 31. 1-battery, solar cell, and electric generator that can act as a power source in an electric circuit. Data from Section 31. 1...
A thick resistor and a thin resistor of the same length and material are connected in series, as shown in Figure 31. 29. Which resistor has $(a)$ the greater potential difference across it and...
Note that the amount of 25k that has already been spent on developing the website is not included in this analysis, as it represents a sunk cost. The decision rule for ARR is that a project should be...
State whether the following statement are True or False: Shareholders equity turnover shows the managements ability in terms of efficiently utilizing the shareholders funds, both with respect to...
What are the two components of a company's income tax provision? What does each component represent about a company's income tax provision?
In Figure ? = 12.0V, R 1 = 2000?, R 2 = 3000? and R 3 = 4000?. What are the potential differences? (a) V A - V B , (b) V B? - V C , (c) V C? - V D , and (d) V A - V C ? R. Ry
In Figure R 1 = 100? R 2 = R 3 = 50.0?, R 4 = 75.0?, and the ideal battery has emf ? = 6.00 V. (a) What is the equivalent resistance? What is i in (b) Resistance 1, (c) Resistance 2, (d) Resistance...
In Figure two batteries of emf ? = 12.0 V and internal resistance r = 0.300? are connected in parallel across a resistance R. (a) For what value of R is the dissipation rate in the resistor a...
Docs Auto Body has budgeted the costs of the following repair time and parts activities for 2009: Doc's budgets 6,000 hours of repair time in 2009. A profit margin of $7 per labour hour will be added...
QUESTION 28 In a perpetual inventory system, the cost of inventory sold is: Debited to accounts receivable. Debited to cost of goods sold. O Not recorded at the time goods are sold. O Credited to...
The following financial statements and additional information are reported. IKIBAN INC. Comparative Balance Sheets June 30, 2019 and 2018 2019 2018 $105,709 69,500 66,800 4,700 246,700 127,eee...

When a carpenter shuts off his circular saw, the 10.0-inchdiameter blade slows from 3984 rpm to 0

Question:

Step by Step Answer:

Picture the Problem A carpenters saw blade rotates about its axis slowing its angular speed at ...View the full answer

Physics

Students also viewed these Mechanics questions