Why is the cycle time for the injection molding of thermosetting polymers significantly longer than that for

Question:

Why is the cycle time for the injection molding of thermosetting polymers significantly longer than that for the thermoplastics?

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Question Posted: May 24, 2016 04:18 AM

See More Questions

What determines the cycle time for (a) Injection molding, (b) Thermoforming, and (c) Compression molding? Explain.
For what types of parts is P/M injection molding an attractive manufacturing process?
Why is it difficult to produce a weld between thermosetting polymers but not difficult with the thermoplastics?
Mr. CFE is the sole proprietor of a hardware store called, The CFE Shop. Mr. CFE has decided to incorporate the business but wishes to minimize any income inclusions on the transfer of his business...
What historical issues may have affected the PCAOB's decision to issue a standard on audit documentation, particularly a standard that emphasizes the retention of audit documentation files?
What were Escoffi ers contributions to the culinary world? AppendixLO1
with u (c, h) = 1 1 (c h)1 . (a) Can optimal consumption follow a geometric Brownian motion under these assumptions? (b) Assume that the excess consumption rate ct = ct ht follows a geometric...
Solve the following LP problem using level curves. MAX: 4X1 + 5X2 Subject to: 2X1 + 3X2 120 4X1 + 3X2 140 X1 + X2 80 X1, X2 0
Ch 17 Assignment #1 CC.FLYING.OFF.THE.SHELVES TMM.17-1 EX.17-01.ALGO EX.17-03.ALGO EX.17-04.ALGO EX.17-05.ALGO Hide or show questions Progress:5/6 items eBook Show Me How Calculator Vertical Analysis...
As a student drives to school, he encounters a traffic signal. This traffic signal stays green for 35 seconds, yellow for 5 seconds, and red for 60 seconds. Assume that the student goes to school...
What is the benefit of a hot runner distribution system in plastic injection molding?
How are the individual components mixed in the reaction injection molding process?
Identify each exercise as an expression or an equation. Then either simplify the expression by performing the indicated operation, or solve the equation, as appropriate. 2 y+1 3 y-y-2 3 y-2
Encouraging you to sit back and watch a full hour of one of your favorite shows on prime-time television. However, instead of getting up during the commercial break or fast forwarding through the...
A family member has been recently diagnosed with a heart condition that requires replacing a heart valve. She points out that if she goes to India, the surgery cost is about 60% cheaper on average...
Based on the case of Bowers Machine Parts. Critically analyze why people were not doing their best and critically explain why hiring a consultant might solve the issue. Justify your answer by using...
Identify a few strategies for sustainability effectiveness. Should sustainability be a corporation's top priority? Why or why not? What are the challenges associated with implementing sustainable...
Answer the following questions for the topic you want to write about. Type your answers in a separate Word document. What is the issue or debatable idea you might write about? What is debatable about...
Review one of the following articles. What are the key takeaways from the article you reviewed? Geerts, J. M., D. Kinnair, P. Taheri P, A. Abraham, J. Ahn, R. Atun, L. Barberia, N. J. Best, R....
Jax Incorporated reports the following data for its only product. The company had no beginning finished goods inventory and it uses absorption costing. $ 57.30 per unit $ 10.30 per unit $ 7.80 per...
A balanced three-phase source supplies power to three loads. The loads are: Load 1: 30 kVA at 0.8 pf lagging Load 2: 24 kW at 0.6 pf leading Load 3: unknown If the line voltage and total complex...
A balanced three-phase source serves the following loads: Load 1: 18 kVA at 0.8 pf lagging Load 2: 10 kVA at 0.7 pf leading Load 3: 12 kW at unity pf Load 4: 16 kVA at 0.6 pf lagging The magnitude of...
A balanced three-phase source supplies power to three loads. The loads are: Load 1: 18 kW at 0.8 pf lagging Load 2: 10 kVA at 0.6 pf leading Load 3: unknown If the line voltage at the load is 208 V...
Required : a- outline the statement of comperhensive income for the year ended 30 november 2021 b- outline the statment of financial position as at 30 November The Trial Balance of Alim Enterprise at...
International business and environment The MIR requires teams to gather current, or the most recently available, data on the markets people, economy, government, and technological status from online...
Consider the following stream of cash flows. The interest rate is 10%. 0 1 2 3 4 5 6 7 100 100 100 200 0 300 300 300 a) What is the value at time 0 of the cash flow stream? b) What is the value of...

Why is the cycle time for the injection molding of thermosetting polymers significantly longer than that for

Question:

Step by Step Answer:

The typical molding cycle in the injection molding of thermoplastics takes ...View the full answer

Materials and process in manufacturing

Students also viewed these Materials Science Engineering questions