A brass bar of length 2.25 m with a square cross section of 90 mm on each

Question:

A brass bar of length 2.25 m with a square cross section of 90 mm on each side is subjected to an axial tensile force of 1500 kN (see figure). Assume that E = 110 GPa and v = 0.34.
Determine the increase in volume of the bar.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Mechanics of Materials

ISBN: 978-0495438076

7th edition

Authors: James M. Gere, Barry J. Goodno

See More Books

Question Posted: Apr 19, 2016 05:38 AM

See More Questions

An aluminum-alloy bar of length 2 meters at room temperature (300 K) is exposed to a temperature of 100C ( = 23 10-6 K-1). What will be the length of this bar at 100C?
A bar of length 2.0 m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the...
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1, as shown in part (a) of the figure. The allowable shear stress in the brass is 12 ksi. (a) What is the maximum permissible value...
Multiple Choice Questions: 1. Which of the following is most likely a topic of discussion in macroeconomics? a. An increase in the price of a pizza b. A decrease in the production of VCRs by a...
The Hills County, Michigan, superintendent of education is responsible for assigning students to the three high schools in his county. He recognizes the need to bus a certain number of students,...
Fraud prevention involves two fundamental activities: (1) a hotline for tips and (2) assessing the risk of fraud and developing concrete responses to mitigate the risks and eliminate opportunities...
E 6-2 Discuss effect of intercompany sale of building Khap Corporation acquired an 80 percent interest in Khun Corporation in 2014. On January 1, 2016, Khap sold a building with a five-year remaining...
The chief accountant for Grandview Corporation provides you with the company's 2011 statement of cash flows and income statement. The accountant has asked for your help with some missing figures in...
Cul de estas afirmaciones con respecto a una prdida fortuita deducible incurrida por un contribuyente individual es CORRECTA? A) Un lmite mnimo de $100 por incidente debe reducir una prdida...
What is the force F on the -10 nC charge in FIGURE P22.42? Give your answer as a magnitude and an angle measured cw or ccw (specify which) from the +x@axis. 8.0 nC 3.0 cm +) 1.0 cm -10 nC 10 nC...
A hollow, brass circular pipe ABC (see figure) supports a load P1 = 26.5 kips acting at the top. A second load P2 = 22.0 kips is uniformly distributed around the cap plate at B. The diameters and...
An angle bracket having thickness t = 0.75 in. is attached to the flange of a column by two 5/8-inch diameter bolts (see figure). A uniformly distributed load from a floor joist acts on the top face...
In Exercises find the eccentricity and the distance from the pole to the directrix of the conic. Then sketch and identify the graph. Use a graphing utility to confirm your results. r 4 5 - 3 sin 0
Caching. CPUs. Hard disk drives. Parallelism. Pipelining. RAM. Registers. Solid-state drives. Dinkleberg 1. (3 points) You know that neighbor who always one-ups you? Apparently, he just bought a...
Information for Question 1 and 2: The National Health Interview Survey is an annual national health survey of people living in about 35,000 randomly selected households in the United States. On the...
Q1. There is trampoline on the ground, and connected to spring of spring constant, k, on the bottom. You are holding a child of mass, M on a H tall building top (H is measured from the trampoline to...
SPSS for intermediate statistics extra problems solutions d. Approximately how much variance in consumers' tendency to purchase the product could be predicted from these variables? If you owned the...
A finance company uses the discount method of calculating interest. The loan principal is $5,000, the interest rate is 10%, and repayment is expected in two years. You will receive 4196.25 X from the...
In Table 4.8, X is the Fahrenheit temperature, and Y is the number of times a cricket chirp in 1 minute. Fit a model to these data. Analyze how well it fits. Table 4.8
What are the principal alloying elements in SAE 4340 steel?
The shaft is subjected to a distributed torque along its length of t = (10x 2 ) N m/m, where x is in meters. If the maximum stress in the shaft is to remain constant at 80 MPa, determine the required...
The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers 150 hp when the shaft is turning at 1000 rev>min. Determine the minimum thickness of the shafts wall...
The drive shaft AB of an automobile is made of a steel having an allowable shear stress of Ï allow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the...
Describe how the following affect the valuation of PPE. a) Cash Discounts b) Deferred Payment Contracts
Lou Barlow, a divisional manager for Sage Company, has an opportunity to manufacture and sell one of two new products for a five - year period. His annual pay raises are determined by his division s...
Consider a 5 year debt with a 15% coupon rate paid semi-annually, redeemable at Php1,000 par. The bond is selling at 90%. The flotation cost is Php50 per bind. The firm's tax bracket is 30%.

A brass bar of length 2.25 m with a square cross section of 90 mm on each

Question:

90 mm 90 mm 1500 KN 1500 kN 2.25 m

Step by Step Answer:

NUMERICAL DATA E 110 GPa v 034 P 1500 kN b 90 mm L 2250 mm INITIAL VOLUME Vol i Lb 2 Vol i 1822 1...View the full answer

Mechanics of Materials

Students also viewed these Mechanics questions