Question: Consider a cut and fill stope in a 4.6 m wide vein where raise and level intervals are 53.3 m. A hydraulic fill is placed

Consider a cut and fill stope in a 4.6 m wide vein where raise and level intervals are 53.3 m. A hydraulic fill is placed along the entire stope length to a height of 3.66 m. If the specific weight of fill is 15.8kN/m3 and the porosity is 35%, how many tons of solids are in the fill and how many liters of water?

Step by Step Solution

★★★★★

3.35 Rating (161 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given A cut and fill stope 46 m wide level raises 5... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

26-E-G-R (298).docx

120 KBs Word File

Students Have Also Explored These Related Geological Engineering Questions!

Consider a cut and fill stope in a 15 ft wide vein where raise and level intervals are 175 ft. A hydraulic fill is placed along the entire stope length to a height of 12 ft. If the specific weight of...

Consider a narrow vein overhand stope using cut and fill, as shown in the sketch. Cemented, hydraulic sand fill of modulus Ef is placed in the stope as mining proceeds up dip in a rock mass of...

A pilot flies horizontally at 1300km/h, at height h = 35 m above initially level ground. However, at time t = 0, the pilot begins to fly over ground sloping upward at angle θ = 4.3o (Figure)....

Consider a narrow vein overhand stope using cut and fill, as shown in the sketch. Cemented, hydraulic sand fill of modulus Ef is placed in the stope as mining proceeds up dip in a rock mass of...

\f\f\fChapter 2 Service Strategy Learning Objectives After completing this chapter, you should be able to: 1. Formulate a strategic service vision. 2. Describe how a service competes using the three...

PROGRAMME HANDBOOK: JANUARY 2016 INTAKE ASSIGNMENT 2: HUMAN RESOURCES DEVELOPMENT Read the case study below and answer the questions that follow. National HRD in Finland, Russia, and South Africa...

Haggerty Company pays its salaried employees monthly on the last day of each month. The annual salary payroll for 2 0 - - follows. Compute the following for the payroll of December 3 1 : If an amount...

Activity 6-3-Footing Forms Refer to Print 6-3 and Quantity Spreadsheet No. 6-3 in the online learner resources. Calculate the linear feet of metal forms required for the footings. In addition,...

I need help finding calculations using the information on the financial sheets attached. Clipboard Number Font Alignment H6 F + INSERT BELOW MSFT INCOME STATEMENT AS ORIGINALLY STATED 2 Gross Profit...

Question 3 3 0 Marks A . A slusher is to be employed to handle material in a cut and fill stoping operation. Scraping over a distance of 3 0 m at a rope speed of 7 6 m m i n . The operating...

Ziebart Corp.'s EBITDA last year was $390,000 (= EBIT + depreciation + amortization), its interest charges were $9,500, it had to repay $26,000 of long-term debt, and it had to make a payment of...

What impression does a passive communicator project to his or her receivers? An assertive communicator? An aggressive communicator?

What type of account is property, plant & equipment? How does an auditor perform audit tests for property, plant and equipment?

Arrow Company began operations at the beginning of 2016. At the end of 2016, Arrow reported taxable income of $ 20,800 and pretax financial income of $ 22,200 because of a single temporary...

Colorado Mines paid $498,500 for the right to extract ore from a 200,000-ton mineral deposit. In addition to the purchase price, Colorado Mines also paid a $500 filing fee, a $1,000 license fee to...

Covenant Truck Company is a large trucking company that operates throughout the United States. Covenant Truck Company uses the units-of-production (UOP) method to depreciate its trucks. The company...

United Truck Company is a large trucking company that operates throughout the United States. United Truck Company uses the units-of-production (UOP) method to depreciate its trucks. United Truck...

Turnip Company purchased an asset at a cost of $10,000 with a ten-year life during the current year. The company uses differing depreciation methods for financial reporting and income tax purposes....

15. LO.3 Provide a description of the corporate reorganizations available under 368(a)(1).

This problem illustrates that the strength of a machine part can sometimes be measured in units other than those of force or moment. For example, the maximum speed that a flywheel can reach without...

A light pressure vessel is made of 2024-T3 aluminum alloy tubing with suitable end closures. This cylinder has a 3 -in OD, a 0.065-in wall thickness, and = 0.334. The purchase order specifies a...

A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external pressure caused by a shrink fit. What maximum pressure would cause the material of the tube to yield?

Give three concrete examples drawn from a programming language with which you are familiar in which a variable is live but not in scope

index

P9-6 Defining and Analyzing Changes in Current Liabilities LO9-1 International Business Machines (IBM) is a leading provider of computer products and services. The company is known for its hardware...