Describe the factors that influence the size of the two weld beads shown in Fig. 12.13?

Question:

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Manufacturing Processes for Engineering Materials

ISBN: 978-0132272711

5th edition

Authors: Serope Kalpakjian, Steven Schmid

See More Books

Question Posted: Jul 18, 2016 09:24 AM

See More Questions

Describe the factors that influence the flattening of the interface after resistance projection welding takes place?
What are some of the factors that influence the selection of a specific casting process as a means of making a product?
What are some of the factors that influence the selection of a furnace type or melt procedure in a casting operation?
An unknown nucleus contains 70 neutrons and has twice the volume of the nickel 60 28 Ni nucleus. Identify the unknown nucleus in the form A Z X. Use the periodic table on the inside of the back cover...
Suppose that in Problem 8 a new toothpaste brand enters the market such that the following transition probabilities exist: What are the new long-run market shares? Which brand will suffer most from...
Addy Weddings uses the balance sheet approach to estimate uncollectible receivables. The aging of receivables on December 31,2021 is shown in part a). Required a) Calculate the required allowance for...
Review the principles for incentive pay described in the frrst section of this chapter. How, if at all, could Walrnart apply these principles to strengthen its effort to promote compliance with legal...
Rollins College is contemplating opening a European campus where students from the main campus could go to take courses for 1 of the 4 college years. At the moment, it is considering five countries:...
Baillie Power leased high-tech electronic equipment from Courtney Leasing on January 1, 2021. Courtney purchased the equipment from Doane Machines at a cost of $259,500, its fair value. (FV of $1, PV...
Your company is considering investing in its own transport fleet. The present position is that carriage is contracted to an outside organization. The life of the transport fleet would be five years,...
Give several applications of electrically conducting adhesives?
Give several applications for fasteners used in various household products and explain why other joining methods have not been used instead?
A simple telephone system consists of two end offices and a single toll office to which each end office is connected by a 1-MHz full-duplex trunk. The average telephone is used to make four calls per...
Hogan Business Systems has a small number of sales on account but is mostly a cash business. Consequently, it uses the direct write-off method to account for uncollectible accounts. During 2011 Hogan...
Bourret Inc. experienced the following events for the first two years of its operations. 2011: 1. Provided $\$ 60,000$ of services on account. 2. Provided $\$ 25,000$ of services and received...
A flowrate of lubricant oil is $5 \mathrm{~kg} / \mathrm{s}$ passing through a Venturi tube. The ratio of areas of the Venturi tube is $0.005 \mathrm{~m}^{2} /0.002 \mathrm{~m}^{2}$. The density...
Sketch on separate axes, in the interval 0 360, the graphs of: In each case show the coordinates of any maximum and minimum points, and of any points at which the curve meets the axes. a y = sec...
The wheel of radius $r=300 \mathrm{~mm}$ rolls to the right without slipping and has a velocity $v_{O}=3 \mathrm{~m} / \mathrm{s}$ of its center $O$. Calculate the velocity of point $A$ on...
Compute the derivative using derivative rules that have been introduced so far. y = cos(9 + 41)
Cable Corporation is 60% owned by Anna and 40% owned by Jim, who are unrelated. It has noncash assets, which it sells to an unrelated purchaser for $100,000 in cash and $900,000 in installment...
A piston cylinder contains argon at 20 lbf/in.2, 60 F, and the volume is 4 ft3. The gas is compressed in a polytropic process to 100 lbf/in.2, 550 F. Calculate the heat transfer during the process.
A small elevator is being designed for a construction site. It is expected to carry four 150 lbm workers to the top of a 300-ft-tall building in less than 2 min. The elevator cage will have a...
Water is in a piston cylinder maintaining constant P at 330 F, quality 90% with a volume of 4 ft3. A heater is turned on heating the water with 10 000 Btu/h. What is the elapsed time to vaporize all...
American Food Services, Incorporated leased a packaging machine from Barton and Barton Corporation. Barton and Barton completed construction of the machine on January 1 , 2 0 2 4 . The lease...
Which of the following statements is true? Financial measures tend to be lag indicators that report on the results of past actions. LA profit center is responsible for generating revenue, but it is...
Andretti Company has a single product called a Dak. The company normally produces and sells 8 0 , 0 0 0 Daks each year at a selling price of $ 5 6 per unit. The company s unit costs at this level of...

Describe the factors that influence the size of the two weld beads shown in Fig. 12.13?

Question:

Step by Step Answer:

The given figure shows the size of weld beads in a Bectronbeam welding b Conventional weld...View the full answer

Manufacturing Processes for Engineering Materials

Students also viewed these Mechanical Engineering questions