Question: Determine the stresses in the plates with the round and square holes subjected to the tensile stresses shown in Figure P7-22. Compare the largest principal

Determine the stresses in the plates with the round and square holes subjected to the tensile stresses shown in Figure P7-22. Compare the largest principal stresses for each plate. Let E = 210 GPa, v = 0.25, and t = 5 mm.

Figure P7-22

I mm rad. each corner 500 mm 25 mm 25-mm radius | KN/m? I KN/m 1 kN/m| 1 kN/m? 500 mm 500 mm

Step by Step Solution

★★★★★

3.50 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The figure above is the maximum principal stress The maximum is 3505 N m 2 T... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

1414-P-T-H-T(1430).docx

120 KBs Word File

Students Have Also Explored These Related Thermodynamics Questions!

Determine the stresses in the plate with the hole subjected to the tensile stress shown in Figure P7-13. Graph the stress variation (x versus the distance y from the hole. Let E = 200 GPa, v = 0.25,...

The steel beam ABCD shown is simply supported at A and supported at B and D by steel cables, each having an effective diameter of 12 mm. The second area moment of the beam is I = 8(105) mm4. A force...

The steel beam ABCD shown is supported at C as shown and supported at B and D by steel bolts each having a diameter of 5/16 in. The lengths of BE and DF are 2 and 2.5 in, respectively. The beam has a...

Background. It is well known that holes produce concentration of stresses. For example, the stress distribution in a continuous rectangular plate subjected to uniaxial tension p is uniform ( Fig . 1...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Q . 2 . An element in plane stress in subjected to stresses x , y and x y ( see the figure ) . Using Mohr's circle, a ) Determine the principle stresses. ( 1 0 % ) b ) Determine the maximum shear...

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Sketch the FBD in 3 D Draw the FBD using two perpendicular planar coordinates. Determine External Forces ( using STATICS ) Determine the force F B , assuming the shaft is running at a constant speed....

Given: frame constructed from hollow rectangular tubes so that bending is about the strong axis ( x - axis ) , as shown. Pinned supports at A and D , pinned connection at C . Report forces in kips,...

please answer all parts and explain fully, this is for study purposes so concepts matter. thank you!!! ( 3 5 ) A fixed, angled member with a solid square cross - section is subjected to the loads...

Students at a local high school were randomly selected to participate in a math fluency program. The program is designed to increase their math fluency. A total of 12 students each took a pretest...

If f(t) = e at cos wtu (t 1), find F(s). Discuss.

The opportunity cost of going to school is highest for someone who a) has to give up a job paying $10 an hour. b) has to give up a job paying $15 an hour. c) loves school. d) has to give up a...

4.74 Unknown to a quality assurance technician, the tensile strengths (in pounds per square inch, psi) for all 500 heavy-duty construction bolts in a recent shipment are as listed in fi le XR04074....

A 900-kg car cruising at a constant speed of 60 km/s is to accelerate to 100 km/h in 4 s. The additional power needed to achieve this acceleration is (a) 56 kW (b) 222 kW (c) 2.5 kW (d) 62 kW (e) 90...

The elevator of a large building is to raise a net mass of 400 kg at a constant speed of 12 m/s using an electric motor. Minimum power rating of the motor should be (a) 0 kW (b) 4.8 kW (c) 47 kW (d)...

A water jet that leaves a nozzle at 60 m/s at a flow rate of 120 kg/s is to be used to generate power by striking the buckets located on the perimeter of a wheel. Determine the power generation...

4. A firm is considering the purchase of an asset whose risk is greater than the current risk of the firm, based on any method for assessing risk. In evaluating this asset, the decision maker should...

write a Code for affine cipher using c++

Using benefit-cost ratio analysis, a 5-year useful life, and a 15% MARR, determine which of the following mutually exclusive alternatives should be selected. Five mutually exclusive investment...