Determine whether or not it is possible to cold work steel so as to give a minimum

Question:

Determine whether or not it is possible to cold work steel so as to give a minimum Brinell hardness of 225, and at the same time have a ductility of at least 12%EL. Justify your decision.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials Science and Engineering An Introduction

ISBN: 978-0470419977

8th edition

Authors: William D. Callister Jr., David G. Rethwisch

See More Books

Question Posted: Apr 29, 2016 03:58 PM

See More Questions

Determine whether or not it is possible to cold work brass so as to give a minimum Brinell hardness of 120 and at the same time have a ductility of at least 20%EL. Justify your decision.
Determine whether or not it is possible to cold work brass so as to give a minimum Brinell hardness of 120 and at the same time have a ductility of at least 20%EL. Justify your decision.
Consider an LTI system with frequency response, The input x[n] to the system is restricted to be real valued and to have a Fourier transform (i.e., x[n] is absolutely summable). Determine whether or...
A client of Park Street's expected a delivery of samples for an event on Friday evening. The order was setup correctly by Park Street, however the vendor that was hired to pick up and deliver the...
The following data were extracted from the income statement of Hestia System Inc: A. Determine for each year (1) The inventory turnover and (2) The number of days' sales in inventory. Round to the...
Purchase Decisions Tom Blackman works in the accounting department of one of the large retail stores in town and has just completed an evaluation of microcomputers to decide which model the store...
Describe a code structure for a firm that decides to capture information about environmental costs. LO.1
In a supercomputer, signal propagation delays are reduced by resorting to high-density circuit arrangements which are cooled by immersing them in a special dielectric liquid. The fluid is pumped in a...
Explain the difference b/w the Free Cash flow stock valuation model and the Divided Discount model. What discount rate is used in the Free Cash flow model and what extra step do you need to take in...
Alpha Romeo paid a $2.1 dividend in the prior year on earnings of $6.25 per share. Alpha Romeo has a target payout ratio of 40% and an adjustment factor of 23%. Assume Alpha Romeo's earnings will...
Equations 7.1a and 7.1b, expressions for Burgers vectors for FCC and BCC crystal structures, are of the form b = a/2(uvw) where a is the unit cell edge length. Also, since the magnitudes of these...
A cylindrical specimen of cold-worked steel has a Brinell hardness of 250. (a) Estimate its ductility in percent elongation. (b) If the specimen remained cylindrical during deformation and its...
Why is it necessary for financial reporting to be subject to (a) mandatory control and (b) statutory control? LO5-1
Aircraft $B$ has a constant speed of $150 \mathrm{~m} / \mathrm{s}$ as it passes the bottom of a circular loop of 400-m radius. Aircraft $A$ flying horizontally in the plane of the loop passes...
A small inspection car with a mass of $200 \mathrm{~kg}$ runs along the fixed overhead cable and is controlled by the attached cable at $A$. Determine the acceleration of the car when the control...
An aircraft $P$ takes off at $A$ with a velocity $v_{0}$ of $250 \mathrm{~km} / \mathrm{h}$ and climbs in the vertical $y^{\prime}-z^{\prime}$ plane at the constant $15^{\circ}$ angle...
If each resistor in Figure P31.75 has resistance $R=5.0 \Omega$, what is the equivalent resistance of the combination? Data from Figure P31.75 wwwwww wwwww www www wwwww
Identify the proper point to recognize expense for each of the following transactions. a. Kat Inc. purchases on credit six custom sofas for $\$ 800$ each in June. Two of the sofas are sold for \(\$...
A three-phase, three-wire CBA system, with an effective line voltage 106.1 V, has a balanced Y-connected load with impedances 5 30 (Fig. 11-26). Obtain the currents and draw the voltage current...
Government is advised to tax goods whose demand curves are inelastic if the goal is to raise tax revenues. If the goal is to discourage consumption, then it ought to tax goods whose demand curves are...
A cylindrical rod of brass originally 10.2 mm (0.40 in.) in diameter is to be cold worked by drawing; the circular cross section will be maintained during deformation. A cold-worked yield strength in...
A cylindrical brass rod having a minimum tensile strength of 450 MPa (65,000 psi), a ductility of at least 13%EL, and a final diameter of 12.7 mm (0.50 in.) is desired. Some brass stock of diameter...
Consider the brass alloy discussed in Problem 7.41. Given the following yield strengths for the two specimens, compute the heat treatment time required at 650oC to give a yield strength of 90 MPa....
Comprehensive Project for WACC and NPV Company A is considering a 4 - year project. They own a piece of land that could be sold for $ 1 0 0 , 0 0 0 . They hired an engineer to evaluate it and she has...
AR by Company To see companies within a particular country, elther click on that country or use the search field in the upper left corner. To return to the map's global view, click on the Home icon...
can anyone help find a news article discussing a corporations use of debt financing? Often times the financial news media will report when a company chooses to issue new bonds or take new loans.

Determine whether or not it is possible to cold work steel so as to give a minimum

Question:

Step by Step Answer:

The tensile strength corresponding to a Brinell hardness of 225 may be determin...View the full answer

Materials Science and Engineering An Introduction

Students also viewed these Thermodynamics questions