From a manufacturing viewpoint, why is it desirable to use standard fasteners and minimize the variety of

Question:

From a manufacturing viewpoint, why is it desirable to use standard fasteners and minimize the variety of fasteners within a given product?

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Question Posted: May 24, 2016 06:40 AM

See More Questions

From a manufacturing viewpoint, why is it desirable for all bends in a product (or component) to have the same radius?
A gas stream containing 40.0mole% hydrogen, 35.0% carbon monoxide, 20.0% carbon dioxide, and 5.0% methane is cooled from 1000C to 10C at a constant absolute pressure of 35.0 atm. Gas enters the...
What does it mean for a separation procedure to be "rugged" and why is it desirable?
Prove this statement: Let f be extended real-valued measurable function on a measurable set D. If f is integrable on D, then the set {D: f 0} is a o-finite set.
Gleason Co. uses the percentage-of-receivables basis to record bad debt expense. It estimates that 1% of accounts receivable will become uncollectible. Accounts receivable are $420,000 at the end of...
Variance analysis for an activity area. CellOne is a cellular phone service reseller, contracting with major cellular operators for airtime in bulk and then reselling service to retail customers....
5 Algunos anunciantes del pas han descubierto que su publicidad puede tener un mejor resultado si publican una gran cantidad de anuncios durante un periodo y luego suspenden por completo sus anuncios...
Ronen Consulting has just realized an accounting error that has resulted in an unfunded liability of $398,930 due in 28 years. In other words, the company will need $398,930 in 28 years. Toni...
Required information Use the following information for the Exercises below. (The following information applies to the questions displayed below.] The Fields Company has two manufacturing departments,...
The comparative consolidated statement of financial position at December 31, Year 2, and the consolidated income statement for Year 2, of Parent Ltd. and its 70%-owned subsidiary are shown below....
What are some of the common causes for failure of mechanically fastened joints?
Characterize the temperature range over which epoxies might be used, typical values of shear strength, and commonly observed curing times.
In a study of the effect of college student employment on academic performance, the following summary statistics for GPA were reported for a sample of students who worked and for a sample of students...
Canis Major Veterinary Supplies Inc. DuPont Analysis Ratios Value Correct/Incorrect Ratios Value Correct/Incorrect Profitability ratios Gross profit margin (%) 50.00 Correct Asset management ratio...
The entrance to Salt Lake City (elevation 3,075 ft at the point of crossing) is grade separated from interstate highway (elevation 3,050 ft at the point of crossing) and will have to be connected....
McKnight Handcraft is a manufacturer of picture frames for large retailers. Every picture frame passes through two departments: the assembly department and the finishing department. This problem...
A deep reinforced concrete member carries two members with factored loads as shown in Figure 2. Material properties: fy 400 MPa, f'e = 50 MPa. a) Sketch a feasible strut and tie model indicating the...
If triangles ABC and DFG are similar triangles and side DF = 218, what is the value of side DG?
A single-phase, 100-kVA, 460/120-V transformer with 3% R and 6% X is powering a 3-KW heater. Determine the total continuous circuit impedance in ohms looking from the source side and the current...
Making use of the tables of atomic masses, find the velocity with which the products of the reaction B10 (n, ) Li7 come apart; the reaction proceeds via interaction of very slow neutrons with...
Figure P3.87 simulates a manifold flow, with fluid removed from a porous wall or perforated section of pipe. Assume incompressible flow with negligible wall friction and small suction Vw _V1... If...
Consider Fig. P3 36 as a general problem for analysis of a mixing ejector pump. If all conditions (p, , V) are known at sections 1 and 2 and if the wall friction is negligible, derive formulas for...
As shown in Fig. P3.90, a liquid column of height h is confined in a vertical tube of cross-sectional area A by a stopper. At t = 0 the stopper is suddenly removed, exposing the bottom of the liquid...
Your firm is planning to invest in an automated packaging plant. Harburtin Industries is an all - equity firm that specializes in this business. Suppose Harburtin ' s equity beta is 0 . 8 7 , the...
Ned Allen opened a medical practice in Los Angeles, California, and had the following transactions during the month of January. (Click the icon to view the January transactions.) Journalize the...
do you need more information or are you working on this? Irene Watts and John Lyon are forming a partnership to which Watts will devote one- half time and Lyon will devote full time. They have...

From a manufacturing viewpoint, why is it desirable to use standard fasteners and minimize the variety of

Question:

Step by Step Answer:

The use of standard fasteners would enable ready ac...View the full answer

Materials and process in manufacturing

Students also viewed these Materials Science Engineering questions