In making a 6-in. cut in a piece of AISI 1020 cold rolled steel that is 1

Question:

In making a 6-in. cut in a piece of AISI 1020 cold rolled steel that is 1 in. thick, the material is fed to a bandsaw blade with teeth having a pitch of 1.27 mm (20 pitch) at the rate of 0.0001 in. per tooth. Estimate the cutting time for the cut.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Question Posted: May 24, 2016 06:23 AM

See More Questions

A piece of sheet metal of thickness t and density ρ is cut and bent into the shape shown. Determine its mass moment of inertia with respect to a line joining points A and B.
A long, thin rod is cut into two pieces, one being twice as long as the other. To the midpoint of piece A (the longer piece), piece B is attached perpendicularly, in order to form the inverted "T"...
A tube, open at only one end, is cut into two shorter (nonequal) lengths. The piece that is open at both ends has a fundamental frequency of 425 Hz, while the piece open only at one end has a...
An investment at 10.47% effective annual rate compounded monthly is equal to an annual percentage rate of: A. 10.99% B. 9.57% C. 10% D. None of the above If the one-year discount factor is 0.8333,...
Multiple Choice Questions 1. The GAO is responsible for all of the following except: a. Developing standards for audits of federal agencies. b. Developing standards for audits of state agencies. c....
What CBOs might be overlooked due to their relatively smaller size?
What is involved in each phase of the unfreezing transformingrefreezing model of planned change?p. 477
In 2015, Ginger Graham, age 46 and wife of Greg Graham engaged in the transactions described below. Determine Gingers gift tax liability for 2015 if she and Greg elect gift splitting and Greg gave...
Question 2 (1 point) On January 1, year 1, ABC. Ltd. purchased a piece of equipment for $480000 plus installation costs of $ 75000 that were necessary to make the equipment operational ABC. Ltd. uses...
Look at the mass spectrum of germanium, Ge. a. Write the isotopic formula for the heaviest isotope of germanium. b. Use the % abundance of each isotope to calculate the relative atomic mass of...
Estimate the approximate force acting in the forward direction during cutting for the conditions stated in Problems 2 and 3.
The strength of a pull broach is determined by its minimum cross section, which usually occurs either at the root of the first tooth or at the pull end. Suppose the minimum root diameter is Dr, the...
Health care is continually in the news. Can (or should) simulation be used to help solve, or at least study, some of the difficult problems associated with health care? Provide at least two examples...
The financial statements for the Columbia Sportswear Company can be found in Appendix A, and Under Armour, Inc.'s financial statements can be found in Appendix B at the end of this book. Required a....
Use the data from SE3-8 to prepare the closing entries for The Decade Company. Close the temporary accounts to income summary. The balance of $\$ 8,500$ in the retained earnings account is from the...
Adjusting Entries The following selected accounts appear in the Birch Company's unadjusted trial balance as of December 31, the end of the fiscal year (all accounts have normal balances): Required...
Closing Entries Use the information provided in E3-5A to prepare journal entries to close the accounts using the Income Summary account. After these entries are posted, what is the balance in the...
Ceva, Inc. manufactures and services jet engines for air carriers. The engines cost $$10$ to $$40$ million each, depending on the specifications and plane. A 10-year service contract for a single...
What factors affect the likelihood that geographic profiling will be useful in identifying a criminal?
At the beginning of the year, Lam Ltd. had total assets of $800,000 and total liabilities of $500,000. Use this information to answer each of the following independent questions. (a) If Lam's total...
A 7 ft m tall steel cylinder has a cross sectional area of 15 ft2. At the bottom with a height of 2 ft m is liquid water on top of which is a 4 ft high layer of gasoline. The gasoline surface is...
A U-tube manometer filled with water, density 62.3 lbm/ft3, shows a height difference of 10 in. What is the gauge pressure? If the right branch is tilted to make an angle of 30 with the horizontal,...
A piston/cylinder with cross-sectional area of 0.1 ft2 has a piston mass of 200 lbm resting on the stops, as shown in Fig. P2.45. with an outside atmospheric pressure of 1 atm, what should the water...
American Food Services, Incorporated leased a packaging machine from Barton and Barton Corporation. Barton and Barton completed construction of the machine on January 1 , 2 0 2 4 . The lease...
Which of the following statements is true? Financial measures tend to be lag indicators that report on the results of past actions. LA profit center is responsible for generating revenue, but it is...
Andretti Company has a single product called a Dak. The company normally produces and sells 8 0 , 0 0 0 Daks each year at a selling price of $ 5 6 per unit. The company s unit costs at this level of...

In making a 6-in. cut in a piece of AISI 1020 cold rolled steel that is 1

Question:

Step by Step Answer:

The cutting speed selected should be around 55 ...View the full answer

Materials and process in manufacturing

Students also viewed these Materials Science Engineering questions