Question: A milling operation is carried out on a 10. inch long, 3.0 inch wide slab of aluminum alloy. The cutter feed is 0.01 in/tooth, and

A milling operation is carried out on a 10. inch long, 3.0 inch wide slab of aluminum alloy. The cutter feed is 0.01 in/tooth, and the depth of cut is 0.125 inches. The cutter is wider than the slab and the diameter is 2.0 inches. It has 25 teeth and rotates at 150 RPM. Calculate:

a. The material removal rate

b. The power required

c. The torque at the cutter

Step by Step Solution

★★★★★

3.46 Rating (179 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Exploring Engineering Introduction Questions!

A hot working operation is carried out at various speeds. The strength constant, C, is 30,000 psi and the strain-rate sensitivity exponent, m, is 0.15. Determine the flow stress if the strain rate is...

A carburizing process is carried out on a 0.10% C steel by introducing 1.0% C at the surface at 980 C, where the iron is FCC. Calculate the carbon content at 0.01 cm, 0.05 cm, and 0.10 cm beneath the...

A flat-rolling operation is being carried out where h0 = 0.2 in., hf = 0.15 in., w0 = 10 in., R = 8 = 0.25, and the average flow stress of the material' 40,000 psi. Estimate the roll force and the...

Allegheny Ludlum Steel! Question: What is your overall evaluation of Allegheny Ludlum Steel's productivity improvement program? Discuss the productivity improvement program at Allegheny Ludlum in...

(a) A drilling operation is required to produce a hole with a diameter of 25 mm and depth of 20 mm at one end of the Aluminum alloy block. If the feed of a 25-mm drill is 0.1 mm/rev and the spindle...

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

make assumptions and calculations to reduce the cycle time and changeover time of these operations, in the table you can see the 12 operations, just make calculations to improve the CT of operations...

2 - A slab milling operation is to be performed on a 3 0 0 m m long workpiece with a width of 1 0 0 m m using a horizontal milling machine. The operation requires the removal of a total depth of 5 m...

Solve it with the arena simulation program. A manufacturing process consists of four operations: milling, planing, drilling and checking. There are four milling, two planing, three drilling and one...

(6) A print and tool paths for producing a part using CNC milling machine is shown in Figure 4. The indicated machine home reference point is a suggested location while the true location must be...

A parallel beam of white light falls on a thin film whose refractive index is equal to n = 1.33. The angle of indices is 1 = 52. What must the film thickness be equal to for the reflected light to be...

A closed rigid container is charged with propene, C3H6, and 150% theoretical air at 100 kPa, 298 K. The mixture is ignited and burns with complete combustion. Heat is transferred to a reservoir at...

Suppose you want to investigate the question Do insurgent attacks in Afghanistan differ by state? What would the variable be ?

=+management to invest the necessary time, resources and effort for marketing collaboration?

Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: = 20.0 kN/m 3 and c u = 60 kN/m 2 . a. Determine the maximum allowable load (Qall) with FS = 3. Use the a method and Table...

Redo Problem 12.3 using Coyle and Castellos methods for estimating both Q p and Q s . Problem 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m 3 and ' = 32....

A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m 3 and ' = 33. Assuming ' = 0.7' and K = 1.4 K o , determine the load-carrying capacity of the...

Evaluate the following slide and make recommendations for improving it. What You Need to Know - The prolect will nin 6 mantha - The juerpose of the propect is te croate a newid procesu for recalling...

Score: 0.5 Of 1 Find the standard deviation, s, of sample data summarized in the frequency distribution table below by using the formula below, where x represents the class midpoint, f represents the...

Please answer A through E! all components needed to answer the questions are in the picture. thank you! bends have a YTM of 16% and wit mature in 8 years. The ifivestment grade borids have a Bx. YTM,...