A part 275 mm long and 75 mm wide is to be milled with a 10 toothed cutter 75 mm in diameter using a feed of 0 10 mm tooth at a cutting speed of 40 x 10 3 mm min The depth of cut is 5 0 mm Determine the material removal rate and the time required to machine the part

Question: A part 275. mm long and 75. mm wide is to be milled with a 10-toothed cutter 75. mm in diameter using a feed of

A part 275. mm long and 75. mm wide is to be milled with a 10-toothed cutter 75. mm in diameter using a feed of 0.10 mm/tooth at a cutting speed of 40. x 10³ mm/min. The depth of cut is 5.0 mm. Determine the material removal rate and the time required to machine the part.

Step by Step Solution

★★★★★

3.38 Rating (167 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given data L 275 mm W 75 mm n 10 teeth D 75 mm f 010 mm min The rotational speed of t... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

1549_605d88e238b8f_841741.pdf

180 KBs PDF File

1549_605d88e238b8f_841741.docx

120 KBs Word File

Students Have Also Explored These Related Exploring Engineering Introduction Questions!

A telescope is 275 mm long and has an objective lens with a focal length of 257 mm. (a) What is the focal length of the eyepiece? (b) What is the magnification of this telescope?

The surfaces of two concentric spheres having radii of 75 and 100 mm are maintained at 325 K and 275 K, respectively. (a) If the space between the spheres is filled with nitrogen at 5 atm, estimate...

A simply supported composite beam 3 m long carries a uniformly distributed load of intensity q = 3.0 kN/m (see figure). The beam is constructed of a wood member, 100 mm wide by 150 mm deep,...

2 0 . 5 ( A ) ( USCS units ) A turning operation is performed using a rake angle of 1 5 . Cutting speed = 2 0 0 f t m i n , feed = 0 . 0 1 2 i n r e v , and depth of cut = 0 . 1 0 0 i n . The chip...

Question 2 ( 1 * 3 = 3 marks ) ; A slab milling operation will take place on a part 3 0 0 mm long and 4 0 mm wide. A helical cutter 7 5 mm in diameter with 1 0 teeth will be use. If the feed per...

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

Solutions from Montgomery, D. C. (2012) Design and Analysis of Experiments, Wiley, NY Chapter 6 k The 2 Factorial Design Solutions 6.1. An engineer is interested in the effects of cutting speed (A),...

CASE 6 Sambandam Spinning Mills Ltd- Capacity Growth and Managing of Inventory Inventory management and procurement planning It was February 2009 when Saravanan, Head of Production Planning, was...

A steel wire 2.2 mm in diameter and 275 mm long is pulled in tension with a load of 175 N, which produces only elastic deformation. (a) Calculate the resulting strain. (b) An aluminum wire having the...

2 4 . 4 6 A slab - milling operation will take place on a part 2 0 0 mm long and 5 0 mm wide. A helical cutter 8 0 mm in diameter with 1 2 teeth will be used. If the feed per tooth is 0 . 5 m m /...

The Ministry of Basic Education is currently using Microsoft office 2010, recently their ICT coordinator has recommended the ministry to use Office 365. You have been tasked to write a report to the...

Assume that Valhalla decides to make the investment: What valuation do you think is appropriate at an assumed discount rate of 50%? What would be Valhallas expected IRR from the investment at a $5...

Multiple Choice An accourting change that should be reponed prospectively. An accouring change than should be reported by restiting the financia itabemeres of al prior peliods presented. A correction...

=+2 Does the company have the commitment of senior

Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the a method and Table 12.11 for determining the skin friction and...

A concrete pile 15.24 m long having a cross section of 406 mm 406 mm is fully embedded in a saturated clay layer for which g sat = 19.02 kN/m 3 , = 0, and c u = 76.7 kN/m 2 . Determine the...

Redo Problem 12.10 using the l method for estimating the skin friction and Meyerhofs method for the point load estimation. Problem 12.10 A concrete pile 15.24 m long having a cross section of 406 mm ...

QUESTION 3 1 points You're trying to save to buy a new $210,000 Ferrari You have 538,000 today that can be invested at your bank. The bank pays 4 1 percent annual interest on its accounts, How long...

SCENARIO 4-1 The balance sheet and income statement shown below are for Byrd Inc, and the data are to be used for the following questions. Note that the firm has no amortization charges, it does not...

You have the following rates of return for a risky portfolio. Assume that the stock pays na dividends 9 Year 2018 5 Dant Beginning of Year Price $55 $60 $56 $59 of Shares Bought or Sold 160 bought...