FREE Trial
Answered step by step
Verified Expert Solution
Link Copied!

Question

1 Approved Answer

A 75 g, 37-cm-long rod hangs vertically on a frictionless, horizontal axle passing through its center. A 15 g ball of clay traveling horizontally at

A 75 g, 37-cm-long rod hangs vertically on a frictionless, horizontal axle passing through its center. A 15 g ball of clay traveling horizontally at 2.7 m/s hits and sticks to the very bottom tip of the rod. To what maximum angle, measured from vertical, does the rod (with the attached ball of clay) rotate?

Express your answer in degrees. =?

Step by Step Solution

There are 3 Steps involved in it

Step: 1

blur-text-image

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

blur-text-image

Step: 3

blur-text-image

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Electromagnetics

Electromagnetics

Authors: B.B. Laud

3rd Edition

8122430554, 9788122430554

More Books

Students also viewed these Physics questions

Question

★★★★★
Koehler (see Exercise E24-14) makes handheld calculators in two models-basic and professional-and wants to refine its costing system by allocating overhead using departmental rates. The estimated...

Answered: 1 week ago

Question

★★★★★
What are the three types of professional responsibility?

Answered: 1 week ago

Question

★★★★★
What aspects of a salespersons behavior influences the customers decisions the most?

Answered: 1 week ago

Question

★★★★★
A. Identify ONE type of boundary data shown on the map.B. Identify the region of the United States where most dairy farms are located.C. Identify ONE spatial pattern shown on the map.D. Describe the...

Answered: 1 week ago

Question

★★★★★
Opunui Corporation has two manufacturing departments--Molding and Finishing. The company used the following data at the beginning of the year to calculate predetermined overhead rates: Molding...

Answered: 1 week ago

Question

★★★★★
Second Chance Welding rebuilds spot welders for manufacturers. The following budgeted cost data for 2020 is available for Second Chance. The company desires a $37 profit margin per hour of labor and...

Answered: 1 week ago

Question

★★★★★
A pony, tied to the end of a lead, can walk in a full circle, a distance of 56.55 meters. About how long is its lead? A. 28.3 meters B. 18.0 meters C. 9.0 meters D. 7.5 meters

Answered: 1 week ago

Question

★★★★★
2. For an idealized slipper-pad bearing, the bottom wall moves at a constant velocity U and the upper block is fixed. Both the moving and fixed walls are non- permeable. If the velocity within the...

Answered: 1 week ago

Question

★★★★★
4. The monthly profits of Hi-Mark corporation were organized into a frequency distribution. The mean of monthly profits was computed to be $105 600, the median $104 700, and the mode $104 200. (a)...

Answered: 1 week ago

Question

★★★★★
Ralph Young was a commercial tour boat operator on the northern coast of Kauai, Hawaii. He was licensed by the state of Hawaii to operate his boat in Hanalei Bay. The U . S . Department of...

Answered: 1 week ago

Question

★★★★★
A stainless-steel bar is heat up to 1400K and cooldown to improve the hardness of the metal is removed from an furnace and cool down by immersing it in 15 kg of water at 27C. appropriate constant...

Answered: 1 week ago

Question

★★★★★
2. In this chapter, the reader should reflect on the following concepts: emo-tional information, concrete information, local information, the reference object, consensus information, conflict...

Answered: 1 week ago

Question

★★★★★
11. Give two examples of each of the following heuristic assessment mechanisms. a) We use the information that is currently accessible. b) We assume an initial anchor point (value). c) We compare to...

Answered: 1 week ago

Question

★★★★★
4. Give an example of how the consistency principle can be used to influence others.

Answered: 1 week ago

Previous Question Next Question