Question: Design a two-stage decimator for the following specifications: Decimation factor: D = 100 Passband: 0 lessthanorequalto F lessthanorequalto 60 Hz Transition band: 60 lessthanorequalto F

Design a two-stage decimator for the following specifications: Decimation factor: D

Design a two-stage decimator for the following specifications: Decimation factor: D = 100 Passband: 0 lessthanorequalto F lessthanorequalto 60 Hz Transition band: 60 lessthanorequalto F lessthanorequalto 65 Hz Passband ripple: dergree_1 = 10^-1 Stopband attenuation: delta_2 = 10^-3 Sampling frequency: F_sampling = 5 X 10^4 Hz Use MATLAB to plot |H_0(omega)|, |H_1(w)| and |tf(omega)| Where H_0(omega)) denotes the frequency response of the filter in stage H_1(omega) denotes the frequency response of the filter in stage 2 H(omega) denotes the frequency response of the equivalent filter if the system is a single-stage decimator

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Design a two-stage decimator for the following specifications D = 100 0

Q4: Enumerate the procedure involved in multistage implementation of a multi-rate system, Design a two-stage decimator for the following specifications D=100 Passband: 0

Problem 1 0 . ( 1 5 points ) Design a two - stage amplifier such that the output of the first stage is V 1 = - 3 Vin and the output of the second stage is Vout = - V 1 . ( Answer: Many possible )...

write Verilog 2001 code for this Based on Task 1, design a two-stage pipelined integer multiplier by attaching input/output registers, and inserting stage registers, as shown on Page 16 of Lecture...

The objective of this part of the project is to design a two-stage operational amplifier. The two-stage amplifier should satisfy the following specifications: Small signal gain > 90 dB 3-dB bandwidth...

Design a two - stage differential input - output amplifier using CMOSP 0 . 1 8 technology to meet the following specifications. Differential pair tail current = 5 4 0 uA Total gain > 3 0 0 Total...

Project Description: In this project, you will design a two - stage digital system to monitor and regulate the temperature in two zones of a greenhouse ( Zone A and Zone B ) . The system will use...

Objective: Design a controller for the heading control of the aircraft system represented by the block diagram shown in figure 1. a) Determine the minimum value of the gain K when Gc(s)-K, so that...

For this project, students will design a two - stage reverted spur gear speed reducer to accommodate a reduction in speed from 1 8 0 0 rpm ( gear 2 ) at the input shaft ( driven directly by an...

Design Problem Two - stage compression refrigeration system operating between the pressure limits of 1 . 4 and 0 . 1 MPa . The working fluid is refrigerant - 1 3 4 a . The refrigerant leaves the...

Plot the nucleate boiling heat flux for saturated water at atmospheric pressure on a large, horizontal polished copper plate, over the excess temperature range 5C

Use the Excel output in Figure 14.9(c) to do (1) through (6) for each of 0, 1, 2. and 3. Figure 14.9(c) (c) Excel output for the Fresh detergent case (sample size: n = 30) Coefficients 7.5891 2.3577...

Over a certain period, large - company stocks had an average return of 1 2 . 0 9

Seved Help 14 Wisconsin Snowmobile Corp. is considering a switch to level production Cost efficiencies would occur under level production, and aftertax costs would decline by $31,500, but inventory...

7. A group of managers (N25) participated in the problem-solving module of a leadership development program two weeks ago. The module consisted of two days in which the group focused on the correct...

9. What metrics might be useful for evaluating the effectiveness of a companys training function? Discuss and rate their importance.

10. What acceptable methods can be used to show the costs and benefits of training without collecting statistics and conducting analyses? Explain these methods and their strengths and weaknesses...