Question: Every material obeys the Hookes law within: Elastic and plastic region Until tensile stress Until yield point Limit of proportionality

Every material obeys the Hooke’s law within:


Elastic and plastic region

Until tensile stress

Until yield point

Limit of proportionality

Step by Step Solution

★★★★★

3.44 Rating (154 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Answer Every material obeys Hookes law ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

The beam is made of an elastic perfectly plastic material for which Ï Y = 250 MPa. Determine the residual stress in the beam at its top and bottom after the plastic moment M p is applied and...

Q:

The beam is made of elastic perfectly plastic material for which Ï Y = 345 MPa. Determine the maximum elastic moment and the plastic moment that can be applied to the cross section. 100 mm 100...

Q:

The beam is made of an elastic perfectly plastic material for which Ï Y = 200 MPa. If the largest moment in the beam occurs within the center section aa, determine the magnitude of each force P...

Q:

Every material obeys the Hooke s law within: Group of answer choices Elastic and plastic region Until yield point Limit of proportionality Until tensile stress

Q:

Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality

Q:

Objectives 1 ) Conduct the tensile test and obtain the force - elongation data and diagram for the tested materials. 2 ) Plot the stress - strain diagrams for the tested materials. 3 ) Measure the...

Q:

Hooke's law holds good up to yield point limit of proportionality elastic limit plastic limit Question 2 ( 1 point ) It is equal and opposite to the forces applied to a body which tend to elongate it...

Q:

Elsa purchased 500 shares of Anna Bhd for RM5 per share using an initial margin of 60%. Given the maintenance margin of 30%, calculate the return on invested capital if Elsa holds the stock for 6...

Q:

How to solve Figure 1 : A Tensile Load is Applied to a Material. A standard tensile specimen is used in this test as shown in figure 2 with either a circular or a rectangular cross - section. This...

Q:

******************************************************************************** PROGRAM DESCRIPTION This program reads in a set of Cartesian coordinates as arrays. Then the Cartesian coordinates...

Q:

In N.A.H. v. S.L., the Colorado Supreme Court had to resolve a dispute between a man presumed to be a father based on genetic testing and a man presumed to be a father based on his marriage to the...

Q:

When measuring static deflection of the vibration system as shown in the figure, it was 0.075m, and when measuring the static deflection after removing object B, it was 0.05m. When object B has a...

Q:

Express each of the following as a fraction in its simplest form. + 4 3 a+4 2 I 3 (b) 2b b+c 2 3 (c) + d-5 2d+3 (d) f+5 J-1 11 2 3 2 (e) (f) 3h-7 6-5h k-1 k-1 3 5 2 3 (g) (h) + 4m 1 2m+1 n-2 (n (n-2)

Q:

A 2000-turn solenoid is 2.0 m long and 15 cm in diameter. The solenoid current is increasing at 1.0 kA/s. (a) Find the current in a 10-cm-diameter wire loop with resistance 5.0 lying inside the...

Q:

Electrons are much more readily liberated from metals than from nonmetals by irradiation with visible or ultraviolet light. Can you explain why this is true? From metals of what group would you...

Q:

Purpose: Learn about the U.S. Securities and Exchange Commission (SEC). Instructions Go to the U.S. SEC website and then choose About to answer the following questions. a. How many enforcement...

Q:

A 20-year loan requires semiannual payments of $808.15 including interest at 3.8% com-pounded semiannually. a. What was the original amount of the loan? b. What is the loan's balance 81 years later...

Q:

A uniform distribution is defined over the interval from 6 to 10. a. What are the values for a and b? b. What is the mean of this uniform distribution? c. What is the standard deviation? d. Show that...

Q:

Example problem for this equation Relative velocity for an airplane: tot =Vp+Vw , P= plane, W = wind Weight: w = mg

Q:

The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases linearly from w = 0 at x = 0 to w = w 0 at x = a, and then decreases linearly to w = 0...

Q:

A steel alloy core is bonded firmly to the copper alloy tube to form the shaft shown. If the materials have the Ï-γ diagrams shown, determine the torque resisted by the core and the...

Q:

If the allowable tensile and compressive stress for the beam are (Ï allow ) t = 2 ksi and (Ï allow ) c = 3 ksi, respectively, determine the maximum moment M that can be applied on the cross...

Q:

1.5. A GSS asked subjects whether astrologythe study ofstar signshas some scientific truth (GSS question SC1TEST3). Of 1245 sampled subjects, 651 responded definitely or probably true, and 594...

Q:

46.Explain how game theory problems (that is, decision-making problems in which there is some opponent) can be analyzed using the same techniques which are used in decision-making under uncertainty....

Q:

1.13. For the statistical software your instructor has chosen for your course, find out how to access the software, enter data, and print any data files that you create. Create a data file using the...