I want help with this code:

I want both LEDs blinking when i touch the wire that connected to pin1.4 by hand. Whenever i let it go, they stop blinking. I have only got into making them blinking all time without stopping . Please help fixing this::::::

//****************************************************************************** // MSP430G2xx3 Demo - Capacitive Touch, Pin Oscillator Method, 1 button // // Description: Basic 1-button input using the built-in pin oscillation feature // on GPIO input structure. PinOsc signal feed into TA0CLK. WDT interval is used // to gate the measurements. Difference in measurements indicate button touch. // LEDs flash if input is touched. // // ACLK = VLO = 12kHz, MCLK = SMCLK = 1MHz DCO // // MSP430G2xx3 // ----------------- // /|\| XIN|- // | | | // --|RST XOUT|- // | | // | P1.4|<--Capacitive Touch Input 1 // | | // LED 2 <--|P1.6 | // | | // LED 1 <--|P1.0 | // | | // | | // /* Define User Configuration values */ /*----------------------------------*/ /* Defines WDT SMCLK interval for sensor measurements*/

#include "msp430g2553.h"

/* Define User Configuration values */ /*----------------------------------*/ /* Defines WDT SMCLK interval for sensor measurements*/ #define WDT_meas_setting (DIV_SMCLK_512) /* Defines WDT ACLK interval for delay between measurement cycles*/ #define WDT_delay_setting (DIV_ACLK_512)

/* Sensor settings*/ #define KEY_LVL 150 // Defines threshold for a key press /*Set to ~ half the max delta expected*/

/* Definitions for use with the WDT settings*/ #define DIV_ACLK_512 (WDT_ADLY_16) // ACLK/512 #define DIV_SMCLK_512 (WDT_MDLY_0_5) // SMCLK/512

// Global variables for sensing unsigned int base_cnt, meas_cnt; int delta_cnt; char key_pressed; int cycles; /* System Routines*/ void measure_count(void); // Measures each capacitive sensor void pulse_LED(void); // LED gradient routine

/* Main Function*/ void main(void) { unsigned int i,j; WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer BCSCTL1 = CALBC1_1MHZ; // Set DCO to 1MHz DCOCTL = CALDCO_1MHZ; BCSCTL3 |= LFXT1S_2; // LFXT1 = VLO

IE1 |= WDTIE; // enable WDT interrupt P2SEL = 0x00; // No XTAL P1DIR = 0x41; // P1.0 & P1.6 = LEDs P1OUT = 0x00;

__bis_SR_register(GIE); // Enable interrupts

measure_count(); // Establish baseline capacitance base_cnt = meas_cnt;

for(i=15; i>0; i--) // Repeat and avg base measurement { measure_count(); base_cnt = (meas_cnt+base_cnt)/2; }

/* Main loop starts here*/ while (1) { j = KEY_LVL; key_pressed = 0; // Assume no keys are pressed

measure_count(); // Measure all sensors

delta_cnt = base_cnt - meas_cnt; // Calculate delta: c_change

/* Handle baseline measurment for a base C decrease*/ if (delta_cnt < 0) // If negative: result increased { // beyond baseline, i.e. cap dec base_cnt = (base_cnt+meas_cnt) >> 1; // Re-average quickly delta_cnt = 0; // Zero out for pos determination } if (delta_cnt > j) // Determine if each key is pressed { // per a preset threshold j = delta_cnt; key_pressed = 1; // key pressed } else key_pressed = 1;

/* Delay to next sample, sample more slowly if no keys are pressed*/ if (key_pressed) { BCSCTL1 = (BCSCTL1 & 0x0CF) + DIVA_0; // ACLK/(0:1,1:2,2:4,3:8) cycles = 20; } else { cycles--; if (cycles > 0) BCSCTL1 = (BCSCTL1 & 0x0CF) + DIVA_0; // ACLK/(0:1,1:2,2:4,3:8) else { BCSCTL1 = (BCSCTL1 & 0x0CF) + DIVA_3; // ACLK/(0:1,1:2,2:4,3:8) cycles = 0; } } WDTCTL = WDT_delay_setting; // WDT, ACLK, interval timer

/* Handle baseline measurment for a base C increase*/ if (!key_pressed) // Only adjust baseline down { // if no keys are touched base_cnt = base_cnt - 1; // Adjust baseline down, should be } // slow to accomodate for genuine pulse_LED(); // changes in sensor C

__bis_SR_register(LPM3_bits); } } // End Main /* Watchdog Timer interrupt service routine*/ #if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__) #pragma vector=WDT_VECTOR __interrupt void watchdog_timer(void) #elif defined(__GNUC__) void __attribute__ ((interrupt(WDT_VECTOR))) watchdog_timer (void) #else #error Compiler not supported! #endif { TA0CCTL1 ^= CCIS0; // Create SW capture of CCR1 __bic_SR_register_on_exit(LPM3_bits); // Exit LPM3 on reti } /* Measure count result (capacitance) of each sensor*/ /* Routine setup for four sensors, not dependent on NUM_SEN value!*/

void measure_count(void) {

TA0CTL = TASSEL_3+MC_2; // TACLK, cont mode TA0CCTL1 = CM_3+CCIS_2+CAP; // Pos&Neg,GND,Cap

/*Configure Ports for relaxation oscillator*/ /*The P2SEL2 register allows Timer_A to receive it's clock from a GPIO*/ /*See the Application Information section of the device datasheet for info*/ P1DIR &= ~ BIT4; // input for pin 1.4 P1SEL &= ~ BIT4; P1SEL2 |= BIT4;

/*Setup Gate Timer*/ P1SEL2 |= BIT4; WDTCTL = WDT_meas_setting; // WDT, ACLK, interval timer TA0CTL |= TACLR; // Clear Timer_A TAR __bis_SR_register(LPM0_bits+GIE); // Wait for WDT interrupt TA0CCTL1 ^= CCIS0; // Create SW capture of CCR1 meas_cnt = TACCR1; // Save result WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer P1SEL2 &= ~BIT4;

}

void pulse_LED(void) { if(key_pressed) { P1OUT ^=0x41; }else{ P1OUT = 0; }

}