Old MathJax webview

quality management. please give me a full answer to this question

7. Perform FMEA by considering the four (4) most significant problems. Use table 4 to determine FMEA rating criteria. 7.1. Prioritize the causes and develop corrective actions Qty 38 31 35 25 40 48 32 17 55 23 35 19 Table 1: Punch list items grouped Contractor Non-Conformity Carpentry Wall finish not smooth, repair Carpentry Door magnet: at stop not working well, adjust. Carpentry Mill work face frame uneven, repair/replace. Carpentry Trim base joint not smooth, repair. Carpentry Trim damaged, repair. Carpentry Door latch: does not work, repair. Ceiling Ceiling tile adjust to sit in grid Ceiling Drywall surface at ceiling not smooth or damaged, repair Ceiling Clean ceiling grid Ceiling Clean mechanical grille, wipe down Ceiling Ceiling tile chipped, replace Ceiling Ceiling tile clean, touch up, or replace Plumping Plumbing: leaky faucet Plumping Plumbing: installation incomplete. Plumping Plumbing: escutcheon loose, adj., tighten. Plumping Neoprene gasket: not flush to edge of hardware, trim or adjust. Plumping Plumbing: broken faucet Plumping Toilet valve knob missing. Plumping Shower Leak at inside corner adj. to toilet room. Electrical Electrical: incomplete switch installation. Electrical Electrical: Exposed Wires Electrical Electrical: Wrong Location for outlet - patch Electrical Electrical: Missing Faceplate Electrical Access panel: tighten shut, touch up Electrical Light fixture: on/off switching not working, repair Electrical Light installation incomplete 37 27 30 17 27 45 22 25 33 23 28 15 35 37 Table 4: FMEA scoring table Rating Severity 1 Not noticeable to customer Criteria Occurrence Highly unlikely 1 out regulatory compliance endangered, of 2 opportunities without warning Unlikely to detect failure: 20% 8 9 Very unlikely to detect failure: 10% Highly unlikely to detect failure: 5% Nearly certain not to detect failure, or no controls in place 10 7. Perform FMEA by considering the four (4) most significant problems. Use table 4 to determine FMEA rating criteria. 7.1. Prioritize the causes and develop corrective actions Qty 38 31 35 25 40 48 32 17 55 23 35 19 Table 1: Punch list items grouped Contractor Non-Conformity Carpentry Wall finish not smooth, repair Carpentry Door magnet: at stop not working well, adjust. Carpentry Mill work face frame uneven, repair/replace. Carpentry Trim base joint not smooth, repair. Carpentry Trim damaged, repair. Carpentry Door latch: does not work, repair. Ceiling Ceiling tile adjust to sit in grid Ceiling Drywall surface at ceiling not smooth or damaged, repair Ceiling Clean ceiling grid Ceiling Clean mechanical grille, wipe down Ceiling Ceiling tile chipped, replace Ceiling Ceiling tile clean, touch up, or replace Plumping Plumbing: leaky faucet Plumping Plumbing: installation incomplete. Plumping Plumbing: escutcheon loose, adj., tighten. Plumping Neoprene gasket: not flush to edge of hardware, trim or adjust. Plumping Plumbing: broken faucet Plumping Toilet valve knob missing. Plumping Shower Leak at inside corner adj. to toilet room. Electrical Electrical: incomplete switch installation. Electrical Electrical: Exposed Wires Electrical Electrical: Wrong Location for outlet - patch Electrical Electrical: Missing Faceplate Electrical Access panel: tighten shut, touch up Electrical Light fixture: on/off switching not working, repair Electrical Light installation incomplete 37 27 30 17 27 45 22 25 33 23 28 15 35 37 Table 4: FMEA scoring table Rating Severity 1 Not noticeable to customer Criteria Occurrence Highly unlikely 1 out regulatory compliance endangered, of 2 opportunities without warning Unlikely to detect failure: 20% 8 9 Very unlikely to detect failure: 10% Highly unlikely to detect failure: 5% Nearly certain not to detect failure, or no controls in place 10