Answered step by step
Verified Expert Solution
Link Copied!

Question

1 Approved Answer

Physical Units Method, Relative Sales-Value-at-Split-off Method, Net Realizable Value Method, Decision Making Sonimad Sawmill, Inc. (SSI), purchases logs from independent timber contractors and processes them

Physical Units Method, Relative Sales-Value-at-Split-off Method, Net Realizable Value Method, Decision Making Sonimad Sawmill, Inc. (SSI), purchases logs from independent timber contractors and processes them into the following three types of lumber products: Studs for residential construction (e.g., walls and ceilings) Decorative pieces (e.g., fireplace mantels and beams for cathedral ceilings) Posts used as support braces (e.g., mine support braces and braces for exterior fences around ranch properties) These products are the result of a joint sawmill process that involves removing bark from the logs, cutting the logs into a workable size (ranging from 8 to 16 feet in length), and then cutting the individual products from the logs, depending upon the type of wood (pine, oak, walnut, or maple) and the size (diameter) of the log. The joint process results in the following costs and output of products during a typical month: Joint production costs: Materials (rough timber logs) $500,000 Debarking (labor and overhead) 50,000 Sizing (labor and overhead) 200,000 Product cutting (labor and overhead) 260,000 Total joint costs $1,010,000 Product yield and average sales value on a per-unit basis from the joint process are as follows: Product Monthly Output Fully Processed Sales Price Studs 80,000 $8 Decorative pieces 5,000 100 Posts 15,000 20 The studs are sold as rough-cut lumber after emerging from the sawmill operation without further processing by SSI. Also, the posts require no further processing. The decorative pieces must be planed and further sized after emerging from the SSI sawmill. This additional processing costs SSI $120,000 per month and normally results in a loss of 10 percent of the units entering the process. Without this planing and sizing process, there is still an active intermediate market for the unfinished decorative pieces where the sales price averages $60 per unit. Required: 1. Based on the information given for Sonimad Sawmill, Inc., allocate the joint processing costs of $1,010,000 to each of the three product lines using the: a. Relative sales-value-at-split-off method. When required, round decimal values to four places before converting to a percentage. For example, .88349 would be rounded to .8835 and entered as "88.35" percent. Monthly Unit Output Sales Price per Unit Relative Sales Value at Split-Off Percent of Sales Allocated Joint Costs Studs $ $ % $ Decorative pieces % Posts % Total $ % $ (Note: Difference due to rounding.) b. Physical units method at split-off. Units Percent x Joint Cost = Allocated Joint Costs Studs % $ $ Decorative pieces % Posts % Total $ c. Estimated net realizable value method. When required, round decimal values to four places before converting to a percentage. For example, .88349 would be rounded to .8835 and entered as "88.35" percent. Fully Processed Monthly Unit Output Sales Price per Unit Net Realizable Value Percent of Value Estimated Allocated Joint Costs Studs $ $ % $ Decorative pieces % Posts % Total $ % $ (Note: Difference due to rounding.) 2. Prepare an analysis for Sonimad Sawmill, Inc., to compare processing the decorative pieces further as it presently does, with selling the rough-cut product immediately at split-off. Sonimad Sawmill, Inc. Analysis Report Monthly unit output Final sales value $ Differential revenue $ Additional contribution from further processing $

Step by Step Solution

There are 3 Steps involved in it

Step: 1

blur-text-image

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

blur-text-image

Step: 3

blur-text-image

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Statistical Analysis Microsoft Excel 2010

Authors: Conrad Carlberg

1st Edition

0789747200, 9780789747204

More Books

Students also viewed these Accounting questions