Question
please fast and I will mark you mc questions and thanks. Expand Question Completion Status: QUESTION 1 The maximum size of an IPv4 packet is
please fast and I will mark you mc questions and thanks.
Expand Question Completion Status: QUESTION 1
The maximum size of an IPv4 packet is _____________.
1024 bytes
4064 bytes
3098 bytes
2048 bytes
1 points
QUESTION 2
A classless address is given as 177.200.180.92/27. What will be the total number addresses available?
32
64
30
62
1 points
QUESTION 3
What is the first useable host address of 168.198.171.72/27?
168.198.171.95
168.198.171.94
168.198.171.65
168.198.171.64
1 points
QUESTION 4
Which of the following command will you use to enable RIPng?
#ipv6 ospf 10 area 0.0.0.0
#no shutdown
#ipv6 router rip 1
#ipv6 eigrp 10
1 points
QUESTION 5
What is the administrative distance for RIP?
100
90
110
120
1 points
QUESTION 6
In packet tracer application, which of the following is used to view the last command applied in CLI?
Up Arrow
Left Arrow
Right Arrow
Ctrl-C
1 points
QUESTION 7
What is the IEEE specification for Spanning Tree Protocol?
803.ud
802.1d
802.9
803.1
1 points
QUESTION 8
The _________________ type of static route uses only the exit interface.
fully specified static route
recursive static route
directly connected static route
default static route
1 points
QUESTION 9
What type of static route is created when the next-hop IP address and exit interface are specified?
recursive static route
fully specified static route
directly connected static route
floating static route
1 points
QUESTION 10
Which type of static route typically uses the distance parameter in the ip route global configuration command?
summary static route
default static route
standard static route
floating static route
1 points
QUESTION 11
In an OSPF router how would you allot a Gigabit Ethernet interface a lower cost than a Fast Ethernet interface?
(config-if)# bandwidth 100
(config-if)# ip ospf cost 100
(config-if)# ip ospf priority 1
(config-router)# auto-cost reference-bandwidth 1000
1 points
QUESTION 12
The _______________ command is used to display the OSPF hello and dead time intervals.
show ip protocols
show ip ospf route
show ip ospf interface
show ip ospf neighbor
1 points
QUESTION 13
One of the following is considered in SPF algorithm to calculate the best path to a destination:
smallest delays
least number of hops
fastest cumulative bandwidth links
fastest single bandwidth link
1 points
QUESTION 14
The administrative distance of OSPF is ______________.
120
110
100
90
1 points
QUESTION 15
Find the odd one out.
Link state response
Link state request
Link state update
Hello packet
1 points
QUESTION 16
What is the default router priority value for all OSPF router?
0
200
255
1
1 points
QUESTION 17
The ________________ command is used to set a trunk port on a 2960 switch interface?
switchport mode trunk
trunk on
trunk all
switchport trunk on
1 points
QUESTION 18
The IEEE standard for frame tagging is ________________________.
802.3U
802.1Q
802.3Z
ISL
1 points
QUESTION 19
Which command is used to make a port trunk port?
port mode trunk
switchport enable trunk
switchport enable mode trunk
switchport mode trunk
1 points
QUESTION 20
How switches identify which frames belong to which VLANs?
Transparent
Frame filtering
Mac filtering
Frame tagging
1 points
Step by Step Solution
There are 3 Steps involved in it
Step: 1
Get Instant Access to Expert-Tailored Solutions
See step-by-step solutions with expert insights and AI powered tools for academic success
Step: 2
Step: 3
Ace Your Homework with AI
Get the answers you need in no time with our AI-driven, step-by-step assistance
Get Started