Scouting and Fingerprinting using Nmap and Ncat The following are required for this lab: A working installation of kali linux Internet Access Functioning VPN from labi nmap and Osat Follow these instructions to verify your omap installation PART 1-NMAP Verify nmap installation using command sudo apt-get install nmap the VMT 11. Dan be Applications Places Terminal Tue 1105 rootkali:- File Et View Search Terminal Help FOOTBALL: + apt-get install nmap Reading package lists... Done Building dependency tree Reading state information... Done nap is already the newest version (7.80 dtsg1 ikalil). nhap set to manually installed. e upgraded, newly installed. @ to remove and 477 not upgraded. FOTOKAT Teresting to this , mes the most pointtarimaides grem. Cut- Use the following network information for this lab: Target network: 10.8.0.0 Subnet Mask: 255.255.255.0 Use ifconfig to check for the tunnel interface created by openen rootkali:- File Edit View Search Terminal Help Inet 192.168.188.147 netrask 255.255.255.0 broadcast 192.168.168.255 Ineto fe80::200:2911 e65135 prefixten 64 scopeid ex20
unspec 08-03-38-86-88-80-88-80-08-03-38-80-88-80-88-60 Laqueuelen 100 UNSPEC) Fux packets 39 bytes 3400 (5.2 Kis Rx errors e dropped overruns afrane e TX packets 52 bytes 2849 (2.7 KB) 1x errors e dropped overruns carriera collisions a 1. Use the map-e argument to map networks over the tunnel. rootekali: # nmap -e tune 10.8.0.0/24 starting Nmap 7.80 ( https:/map.org ) at 2019-09-24 01:26 EDT Nmap scan report for 10.8.0.1 Host is up (0.015s latency). Not shown: 999 filtered ports PORT STAL SERVICE 53/tcp open domain Always ensure onas traffic must be routed over the VPN tunnel for this lab. Use over to answer the following questions. Questions: For each question, provide the terminal command used and Screen shots to produce your answer. If you not able to find anything, justified why? 1. How many hosts are online on the provided network? 2. What host is currently filtering all network ports?. 3. Run a nmap scanning with UDP selected. Why would this provide a different result? 4. What is the total range of network ports? How many does a default nmap scan look at? 5. Run a nmap scan across the entire port range, what changes? Scouting and Fingerprinting using Nmap and Ncat The following are required for this lab: A working installation of kali linux Internet Access Functioning VPN from labi nmap and Osat Follow these instructions to verify your omap installation PART 1-NMAP Verify nmap installation using command sudo apt-get install nmap the VMT 11. Dan be Applications Places Terminal Tue 1105 rootkali:- File Et View Search Terminal Help FOOTBALL: + apt-get install nmap Reading package lists... Done Building dependency tree Reading state information... Done nap is already the newest version (7.80 dtsg1 ikalil). nhap set to manually installed. e upgraded, newly installed. @ to remove and 477 not upgraded. FOTOKAT Teresting to this , mes the most pointtarimaides grem. Cut- Use the following network information for this lab: Target network: 10.8.0.0 Subnet Mask: 255.255.255.0 Use ifconfig to check for the tunnel interface created by openen rootkali:- File Edit View Search Terminal Help Inet 192.168.188.147 netrask 255.255.255.0 broadcast 192.168.168.255 Ineto fe80::200:2911 e65135 prefixten 64 scopeid ex20 unspec 08-03-38-86-88-80-88-80-08-03-38-80-88-80-88-60 Laqueuelen 100 UNSPEC) Fux packets 39 bytes 3400 (5.2 Kis Rx errors e dropped overruns afrane e TX packets 52 bytes 2849 (2.7 KB) 1x errors e dropped overruns carriera collisions a 1. Use the map-e argument to map networks over the tunnel. rootekali: # nmap -e tune 10.8.0.0/24 starting Nmap 7.80 ( https:/map.org ) at 2019-09-24 01:26 EDT Nmap scan report for 10.8.0.1 Host is up (0.015s latency). Not shown: 999 filtered ports PORT STAL SERVICE 53/tcp open domain Always ensure onas traffic must be routed over the VPN tunnel for this lab. Use over to answer the following questions. Questions: For each question, provide the terminal command used and Screen shots to produce your answer. If you not able to find anything, justified why? 1. How many hosts are online on the provided network? 2. What host is currently filtering all network ports?. 3. Run a nmap scanning with UDP selected. Why would this provide a different result? 4. What is the total range of network ports? How many does a default nmap scan look at? 5. Run a nmap scan across the entire port range, what changes
