Question: The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of s KN Find the diameter

The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of s KN Find the diameter of bolt required according to

1. Maximum principal stress theory

2. Maximum shear stress theory

3. Maximum principal strain theory

4. Maximum strain energy theory;

5. Maximum distortion energy theory

Step by Step Solution

★★★★★

3.40 Rating (150 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

The given question is incomplete because the value of the transvers... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

The figure shows a weldment just like that for Probs. 917 to 920 except there are four welds instead of two. Find the safe bending force F if the allowable shear stress in the welds isÏallow....

Q:

The load on a cantilever beam AB has a triangular distribution with maximum intensity q0 (see figure). Determine the angle of rotation θB and the deflection δB at the free...

Q:

As the load on a vertically hanging spiral spring is increased, one would not expect the Fs -versus-x graph line to remain straight, as shown in Figure 7.10d. Explain qualitatively what you would...

Q:

Find the maximum shear stress in a 5 -in-diameter circular saw blade if it runs idle at 5000 rev/min. The saw is 14 gauge (0.0747 in) steel and is used on a 5/8-in-diameter arbor. The thickness is...

Q:

The load on a bolt consists of an axial pull of 1 0 kN together with a transverse shear force of 5 kN . Find the diameter of the bolt required according to 1 . Maximum principal stress theory, 2 ....

Q:

The load on a bolt consists of an axial pull of 1 0 kN together with a transverse shear force of 5 kN . Find the diameter of the bolt required according to 1 . Maximum principal stress theory, 2 ....

Q:

[5]\ 7. A cylindrical shell made of mild steel plate and 1.2m in diameter is to be subjected to an internal pressure of 1.5M(N)/(m) . If the material yields at 200M(N)/(m^(2)) , calculate the...

Q:

[5]\ 7. A cylindrical shell made of mild steel plate and 1.2m in diameter is to be subjected to an internal pressure of 1.5M(N)/(m) . If the material yields at 200M(N)/(m^(2)) , calculate the...

Q:

i need typing answer urgent A thick-walled cylindrical shell made of steel with 50 mm internal radius and 100 mm outer radii is subjected to an internal pressure p. The material properties of the...

Q:

In the design of shafts made of ductile materials subjected to twisting moment and bending moment, the recommended theory of failure is ( A ) maximum principal stress theory ( B ) maximum principal...

Q:

In the design of shafts made of ductile materials subjected to twisting moment and bending moment, the recommended theory of failure is ( A ) maximum principal stress theory ( B ) maximum principal...

Q:

Prepare breakeven analysis and a c-v-p analysis planning future sales using the information below. Breakeven analysis and planning future sales write company has a maximum capacity of 200,000 units...

Q:

"The coronavirus disease (COVID-19) is an infectious disease caused by a new strain of coronavirus. This new virus and disease were unknown before the outbreak began in Wuhan, China, in December 2019.

Q:

The Taylor series for f ( x ) = square root ( 4 x - x ^ 2 ) at a = 2 is Find the first few coefficients.

Q:

Bio Doc Corporation is a biotech company that makes a cancer-treatment drug in a single processing department. Direct materials are added at the start of the process. Conversion costs are added...

Q:

A partnership has the following capital balances: Comprix (35% of gains and losses) . . . . . . . . . ... $150,000 Heflin (40%) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300,000...

Q:

The following data pertain to LawnMate Corporations top-of-the-line lawn mower. Variable manufacturing cost.............................................................$275 Applied fixed...

Q:

The accounting records of Pelham Pharmaceuticals, Inc., reveal the following: Requirement Prepare cash flows from operating activities using the direct method. Also evaluate Pelham's operating cash...

Q:

Hsung Company accumulates the following data concerning a proposed capital investment: cash cost $215,000, net annual cash flows $40,000, present value factor of cash inflows for 10 years 5.65...

Q:

For each scenario, calculate the elasticity and explain its type: a) When the price rises from $120 to $150, the quantity demanded falls from 25 to 18 units. b) As the price declines from $15 to $12,...

Q:

Bolts distributed about a bolt circle are often called upon to resist an external bending moment as shown in the figure. The external moment is 12 kip? In and the bolt circle has a diameter of 8 in....

Q:

A 3 / 4 in - 1 6 UNF X 2 1 / 2 in SAE bolt ( 5 - mark hex head ) is subjected to external load. a ) If the initial bolt tension is 2 0 kip, what is the preload stress in kpsi? b ) This time the...

Q:

A pressure cylinder with a bore diameter (D) of 30 cm is designed for an internal n pressure (p) of 30 kg/cm2. The cylinder cover is fastened to its flangesn by means of 12 bolts which are made of...

Q:

Q 4 . An M 1 0 \ times 1 . 5 ( coarse pitch ) bolt is used to connect two parts ( made of same materials as that of the bolt ) and the area of the parts participating in the load bearing is...

Q:

A bolt is subjected to a variable stress that varies from 100 MPa to 200 MPa. The area of cross section of the bolt is 100 mm and stiffness of the part held together by bolt is three times the...

Q:

Several members are bolted together on such a manner that the deflection per unit load for the bolted members is the same as for the bolt. What axial external load has to be applied to the bolt to...