Topology Note: Do not use 2960 switches. You must select the 3560 model switch in Packet Tracer as shown below. 2960s will not support IPv6 in Packet Tracer. Assessment Objectives Part 1: Configure Basic Device Settings Part 2: Configure Network Infrastructure Settings (VLANs, Trunking, Etherchannel) Part 3: Configure Host Support Part 4: Test and Verify IPv4 and IPv6 End-to-End Connectivity Scenario In this Skills Assessment (SA) you will configure the devices in a small network. You must configure a router, switch and PCs to support both IPv4 and IPv6 connectivity for supported hosts. Your router and switch must also be managed securely. You will configure inter-VLAN routing, DHCP, Etherchannel, and port-security. Required Resources 1 Router (Cisco 4331) 2 Switches (Cisco 3560) 2 PCs Console cables to configure the Cisco IOS devices via the console ports Ethernet cables as shown in the topology VLAN Table VLAN VLAN Name 2 Bikes 3 Trikes 4 Management 5 Parking 6 Native Addressing Table Device / Interface IP Address / Prefix Default Gateway R1 G0/0/1.2 10.19.8.1 /26 N/A R1 G0/0/1.2 2001:db8:acad:a::1 /64 N/A R1 G0/0/1.3 10.19.8.65 /27 N/A R1 G0/0/1.3 2001:db8:acad:b::1 /64 N/A R1 G0/0/1.4 10.19.8.97 /29 N/A R1 G0/0/1.4 2001:db8:acad:c::1 /64 N/A R1 G0/0/1.6 N/A N/A R1 Loopback0 209.165.201.1 /27 N/A R1 Loopback0 2001:db8:acad:209::1 /64 N/A S1 VLAN 4 10.19.8.98 /29 10.19.8.97 S1 VLAN 4 2001:db8:acad:c::98 /64 N/A S1 VLAN 4 fe80::98 N/A S2 VLAN 4 10.19.8.99 /29 10.19.8.97 S2 VLAN 4 2001:db8:acad:c::99 /64 N/A S2 VLAN 4 fe80::99 N/A PC-A NIC DHCP for IPv4 address DHCP for IPv4 default gateway PC-A NIC 2001:db8:acad:a::50 /64 fe80::1 PC-B NIC DHCP for IPv4 address DHCP for IPv4 default gateway S1 VLAN 4 10.19.8.98 /29 10.19.8.97 S1 VLAN 4 2001:db8:acad:c::98 /64 N/A S1 VLAN 4 fe80::98 N/A S2 VLAN 4 10.19.8.99 /29 10.19.8.97 S2 VLAN 4 2001:db8:acad:c::99 /64 N/A S2 VLAN 4 fe80::99 N/A PC-A NIC DHCP for IPv4 address DHCP for IPv4 default gateway PC-A NIC 2001:db8:acad:a::50 /64 fe80::1 PC-B NIC DHCP for IPv4 address DHCP for IPv4 default gateway PC-B NIC 2001:db8:acad:b::50 /64 fe80::1 Note: There is no interface on the router supporting VLAN 5. Instructions Configure Basic Device Settings Configure R1. Configuration tasks for R1 include the following: Task Specification Disable DNS lookup Router name R1 Domain name ccna-lab.com Encrypted privileged EXEC password ciscoenpass Console access password ciscoconpass Set the minimum length for passwords 10 characters Create an administrative user in the local database Username: admin Password: admin1pass Set login on VTY lines to use local database Set VTY lines to accept SSH connections only Encrypt the clear text passwords Configure an MOTD Banner Enable IPv6 Routing Configure Interface G0/0/1 and sub interfaces Set the description Set the IPv4 address Set the IPv6 Link Local Address as fe80::1 Set the IPv6 address Activate Interface Configure the Loopback0 interface Set the description Set the IPv4 address Set the IPv6 address Set the IPv6 Link Local Address as fe80::1 Generate an RSA crypto key 1024 bits modulus Configure S1 and S2. Configuration tasks for the switches include the following: Task Specification S1 S2 Disable DNS lookup Switch name S1 or S2, as appropriate Domain name ccna-lab.com Encrypted privileged EXEC password ciscoenpass Task Specification S1 S2 Disable DNS lookup Switch name S1 or S2, as appropriate Domain name ccna-lab.com Encrypted privileged EXEC password ciscoenpass Console access password ciscoconpass Create an administrative user in the local database Username: admin Password: admin1pass Set login on VTY lines to use local database Set VTY lines to accept SSH connections only Encrypt the clear text passwords Configure an MOTD Banner Generate an RSA crypto key 1024 bits modulus Configure Management Interface (SVI) Set the Layer 3 IPv4 address Set the Ipv6 Link Local Address as FE80::98 for S1 and FE80::99 for S2 Set the Layer 3 IPv6 address Configure Default Gateway Configure the default gateway as 10.19.8.97 for IPv4 Enter score here. Configure Network Infrastructure Settings (VLANs, Trunking, EtherChannel) Configure S1. Configuration tasks for S1 include the following: Task Specification Create VLANs VLAN 2, name Bikes VLAN 3, name Trikes VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native Create 802.1Q trunks that use the native VLAN 6 Interfaces F0/1, F0/2, and F0/5 Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2 Use the LACP protocol for negotiation Configure host access port for VLAN 2 Interface F0/6 Configure port-security on Create VLANs VLAN 3, name Trikes VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native Create 802.1Q trunks that use the native VLAN 6 Interfaces F0/1, F0/2, and F0/5 Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2 Use the LACP protocol for negotiation Configure host access port for VLAN 2 Interface F0/6 Configure port-security on access ports Allow 3 MAC addresses Secure all unused interfaces Assign to VLAN 5, Set to access mode, add a description, and shutdown Configure S2. Configuration tasks for S2 include the following: Task Specification Create VLANs VLAN 2, name Bikes VLAN 3, name Trikes VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native Create 802.1Q trunks that use the native VLAN 6 Interfaces F0/1 and F0/2 Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2 Use the LACP protocol for negotiation Configure host access port for VLAN 3 Interface F0/18 Configure port-security on access ports Allow 3 MAC addresses Secure all unused interfaces Assign to VLAN 5, Set to access mode, add a description, and shutdown Configure Host Support Configure R1 Configuration Tasks for R1 include the following Task Specification Configure Default Routing Create a default routes for IPv4 and IPv6 that direct traffic to interface Loopback 0 Configure IPv4 DHCP for VLAN 2 Create a DHCP pool for VLAN 2, consisting of the last 10 addresses in the subnet only. Assign the domain name ccna- a.net and specify the default gateway address as the router interface address for the subnet involved Create a DHCP pool for VLAN 3, consisting of the last 10 addresses in the subnet only. Task Specification Configure Default Routing Create a default routes for IPv4 and IPv6 that direct traffic to interface Loopback 0 Configure IPv4 DHCP for VLAN 2 Create a DHCP pool for VLAN 2, consisting of the last 10 addresses in the subnet only. Assign the domain name ccna- a.net and specify the default gateway address as the router interface address for the subnet involved Configure IPv4 DHCP for VLAN 3 Create a DHCP pool for VLAN 3, consisting of the last 10 addresses in the subnet only. Assign the domain name ccna- b.net and specify the default gateway address as the router interface address for the subnet involved Configure host computers. Configure the host computers PC-A and PC-B to use DHCP for IPv4 and statically assign the IPv6 GUA and Link Local addresses. After configuring each host computer, record the host network settings with the ipconfig /all command. PC-A Network Configuration Description blank Physical Address blank IP Address blank Subnet Mask blank Default Gateway blank IPv6 Default Gateway blank PC-B Network Configuration Description blank Physical Address blank IP Address blank Subnet Mask blank Default Gateway blank IPv6 Default Gateway blank Test and Verify End-to-End Connectivity Use the ping command to test IPv4 and IPv6 connectivity between all network devices. Note: If pings to host computers fail, temporarily disable the computer firewall and retest. Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails: From To Protocol IP Address Ping Results PC-A R1, G0/0/1.2 IPv4 10.19.8.1 blank PC-A R1, G0/0/1.2 IPv6 2001:db8:acad:a:: 1 blank PC-A R1, G0/0/1.3 IPv4 10.19.8.65 blank PC-A R1, G0/0/1.3 IPv6 2001:db8:acad:b:: 1 blank From To Protocol IP Address Ping Results PC-A R1, G0/0/1.2 IPv4 10.19.8.1 blank PC-A R1, G0/0/1.2 IPv6 2001:db8:acad:a:: 1 blank PC-A R1, G0/0/1.3 IPv4 10.19.8.65 blank PC-A R1, G0/0/1.3 IPv6 2001:db8:acad:b:: 1 blank PC-A R1, G0/0/1.4 IPv4 10.19.8.97 blank PC-A R1, G0/0/1.4 IPv6 2001:db8:acad:c:: 1 blank PC-A S1, VLAN 4 IPv4 10.19.8.98 blank PC-A S1, VLAN 4 IPv6 2001:db8:acad:c:: 98 blank PC-A S2, VLAN 4 IPv4 10.19.8.99. blank PC-A S2, VLAN 4 IPv6 2001:db8:acad:c:: 99 blank PC-A PC-B IPv4 IP address will vary. blank PC-A PC-B IPv6 2001:db8:acad:b:: 50 blank PC-A R1 Loop0 IPv4 209.165.201.1 blank PC-A R1 Loop0 IPv6 2001:db8:acad: 209::1 blank PC-B R1 Loop0 IPv4 209.165.201.1 blank PC-B R1 Loop0 IPv6 2001:db8:acad: 209::1 blank PC-B R1, G0/0/1.2 IPv4 10.19.8.1 blank PC-B R1, G0/0/1.2 IPv6 2001:db8:acad:a:: 1 blank PC-B R1, G0/0/1.3 IPv4 10.19.8.65 blank PC-B R1, G0/0/1.3 IPv6 2001:db8:acad:b:: 1 blank PC-B R1, G0/0/1.4 IPv4 10.19.8.97 blank PC-B R1, G0/0/1.4 IPv6 2001:db8:acad:c:: 1 blank PC-B S1, VLAN 4 IPv4 10.19.8.98 blank PC-B S1, VLAN 4 IPv6 2001:db8:acad:c:: 98 blank PC-B S2, VLAN 4 IPv4 10.19.8.99. blank PC-B S2, VLAN 4 IPv6 2001:db8:acad:c:: 99 blank