Question: Determine the structure stiffness matrix K for the frame. Take E = 29(10 3 ) ksi, I = 700 in 4 , A = 20

Determine the structure stiffness matrixKfor the frame. Take E = 29(103) ksi, I = 700 in4, A = 20 in2for each member.

6. 2 16 ft 20 k - 12 ft- 3. 12 ft

6. 2 16 ft 20 k - 12 ft- 3. 12 ft

Step by Step Solution

★★★★★

3.49 Rating (169 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Member Stiffness MatricesThe origin of the globa... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Structural Analysis Questions!

Q:

Determine the structure stiffness matrix K for the frame. Assume and are fixed. Take E = 200 GPa, I = 300(10 6 ) mm 4 , A = 10(10 3 ) mm 2 for each member. 12 kN/m 1) 2 m - 4 m- 10 kN 2 m 6. (3'

Q:

Determine the structure stiffness matrix K for the frame. Assume is pinned and is fixed. Take E = 200 MPa, I = 300(10 6 ) mm 4 , A = 21(10 3 ) mm 2 for each member. 5 m- 300 kN m, (2. (3 -5

Q:

A square frame carrying a current I = 0.90 A is located in the same plane as a long straight wire carrying a current I0 = 5.0 A. The frame side has a length a = 8.0 cm. The axis of the frame passing...

Q:

Determine the structure stiffness matrix K for the frame. Take E = 2 9 ( 1 0 3 ) k s i , I = 6 0 0 i n 4 , A = 1 7 i n 2 for each member. Assume joints ( 1 ) and ( 3 ) are pinned; joint ( 2 ) is...

Q:

Determine the stiffness matrix K for the frame. Take E = 29(10 3 ) ksi, I = 300 in 4 , A = 10 in 2 for each member. 2 k/ft 12 17 2 (3. 3 20 ft 10 ft 5.

Q:

Q . 7 Determine the structure stiffness matrix K for the frame and the support reaction at the fixed support 1 and 3 . Assume 1 and 3 are fixed. Take E = 2 0 0 GPa, I = 3 0 0 ( 1 0 6 ) m m 4 A = 1 0...

Q:

1 6 - 1 1 . Determine the structure stiffness matrix K , for each member of the frame. Take E = 2 9 ( 1 0 3 ) k s i , I = 7 0 0 i n 4 , A = 3 0 i n 2 for each member. Joint ( 1 ) is pin connected. *...

Q:

Looking for worked solutions to part 2, 3 and 4. Answers are attached Q. 1 The frame structure ABCDE shown in Figure Q. 1 represents an idealised crane geometry and is fully fixed at A and E and has...

Q:

Q 1 [ k ] = E I [ 2 . 3 3 3 0 . 6 6 6 0 . 6 6 6 3 . 3 3 3 ] ii ) [ P ] = [ + 2 6 . 6 7 + 5 4 . 1 7 ] iii ) , 1 = 7 . 2 0 3 1 0 - 4 rads = B ; 2 = 1 4 . 8 1 3 4 1 0 - 4 rads = C ; iv ) M C B = 3 7 . 8...

Q:

Determine the force in each member of the assembly in Prob. 141. Data From Prob. 141. Determine the stiffness matrix K for the assembly. Take A = 0.5 in 2 and E = 29(10 3 ) ksi for each member. (2) 3...

Q:

3) A uniform beam of length L is lifted from its right Support and then dropped. as the beam rotates about its left end. At time to the right end of the beam hits the right support with velocity V,...

Q:

A trust that is required to distribute all of its income annually receives a exemption for the year of A) $0, because it retains no income. B) $100. C) $300. D) $600.

Q:

23. Twenty years from now our disposable income will rise from $30 trillion to $31 trillion. What would your best guess be as to how much consumption will rise? ( LO10 ) a) $50 billion c) $950...

Q:

What does the Tolerance column in Exhibit 15.6 contribute to the answers in Exercises 15.7 and 15.8?

Q:

The buoy is made from two homogeneous cones each having radius r. Find the distance zc to the buoy's center of gravity G. Given: r = 1.5 ft h = 1.2 ft a = 4 ft a

Q:

The buoy is made from two homogeneous cones each having radius r. If it is required that the buoy's center of gravity G be located at zc, determine the height h of the top cone. Given: zc = 0.5 ft r...

Q:

Locate the center of mass zc of the forked lever, which is made from a homogeneous material and has the dimensions shown. Given: a = 0.5 in b = 2.5 in c = 2 in d = 3 in e = 0.5 in

Q:

Answers are given in blue. Please solve only using Excel Functions. Any other explanation other than excel will be rejected. \f\f\f\f

Q:

BKE manufactures carbon capture modules. The firm does not currently pay a dividend and uses all company profits to expand a company-owned lithium mine. Analysts expect BKE to pay a dividend of $1.25...

Q:

Becker Industries is considering an all equity capital structure against one with both debt and equity. The all equity capital structure would consist of 26,000 shares of stock. The debt and equity...